A s s e m b l y
G u i d e
R2600iNetTV
COMMERCIAL FITNESS BIKE
TOOLS & PARTS INCLUDED
MM
MM
5 Allen Wrench
6 Allen Wrench
MM
4 L-Shaped Wrench
Screwdriver
MM
5 L-Shaped Wrench
PARTS BOX
Console Mast Cover, Qty: 1
Water Bottle & Cage, Qty: 1
Heart Rate Chest Strap, Qty: 1
Color-coded Hardware Bags
Assembly Guide
CONSOLE BOX
iNetTV Console
Owner’s Guide
Warranty Card
HARDWARE INCLUDED
ORANGE BAG
GREEN BAG
M8x65L Screw
Quantity: 2
M8 Lock Washer
Quantity: 8
M8 x 15L Screw
Quantity: 4
M8 Lock Washer
Quantity: 4
M8 x 20L Screw
Quantity: 2
M8 x 20L Screw
Quantity: 4
BLUE BAG
BLACK BAG
M8 Lock Washer
Quantity: 6
M8 x 15L Screw
Quantity: 7
M6 x 55L Screw
Quantity: 8
PINK BAG
M6 Lock Washer
Quantity: 8
M8 Lock Washer
Quantity: 4
M8 x 20L Screw
Quantity: 2
STEP
1
ORANGE BAG
• Install the rear foot with the four lock
washers (M8), two inside screws
(M8x65L), and two outside screws
STEP
1
MM
(M8x20L). Tighten with the 5 Allen
wrench.
STEP
2
BLUE BAG
• Slide the rubber boot onto the
console mast.
• Locate the bundle of wires that
comes from the console mast frame
bracket. Wrap the wire tie coming
from the bottom of the console mast
around the bundle of wires. Pull the
wire tie with the bundle of wires up
through the top of the console mast
while simultaneously sliding the mast
into the frame bracket.
STEP
2
• Secure the console mast to the
frame bracket with six lock washers
(M8) and six screws (M8x15L).
MM
Tighten with the 5 Allen wrench.
Place the seventh screw (M8x15L) in
the rear of the frame bracket and
tighten until snug.
• Slide the console mast boot down
and snap it into place on the side
cover.
• Remove the screws located half
way up the console mast with the
Phillips screwdriver. Attach the water
bottle bracket to the console mast with
these two screws. Insert the water
bottle.
5
STEP
3
PINK BAG
STEP
3
• Mount the upper handlebars to the
console mast using two lock washers
(M8) and two screws (M8x20L).
MM
Tighten with the 5 Allen wrench.
STEP
4
CONSOLE
• Remove the six mounting screws
from the back of the console. Set the
console into place on the console
mast and secure it with the six screws
you just removed. Tighten with the
Phillips screwdriver. Connect the wires
to the proper plugs in the back of the
console (see diagram).
STEP
4
1 - Co-Axial Cable TV
2 - USB - B
3 - USB - A
1
2
3
4
5
6
7
8
4 - VGA (PC Video)
5 - Video IN
6 - Audio - R
7 - Audio - L
9
WIRES
8 - Microphone
9 - Heart Rate Reciever 1
10 - Heart Rate Reciever 2
11 - 20 Pin Connector
12 - Power Plug
10
12
13
11
13 - Miles/Kilometers Switch
14 - Data Port
14
6
STEP
5
GREEN BAG
• Attach the seat frame to the sliding
seat bracket using four socket head
MM
cap screws (M8x20L) and the 6
Allen wrench.
• Connect Wires A on the seat
handlebar to Wires B on the sliding
seat bracket. Attach the seat
handlebars to the sliding seat bracket
using four lock washers (M8) and four
Wires A
MM
screws (M8x15L). Tighten with the 5
Allen wrench.
STEP
5
Wires B
7
STEP
6
BLACK BAG
• Secure the Lumbar controlled seat
back and the seat bottom to the seat
frame with eight lock washers (M6)
and eight screws (M6x55L). Tighten
MM
with the 4 Allen wrench.
• Snap the plastic seat cover into
place on the back of the Lumbar
controlled seat.
STEP
6
500 South CP Avenue
•
P.O. Box 280
•
Lake Mills. WI 53551
fax 1.920.648.3373
toll free 1.800.335.4348
•
phone 1.920.648.4090
•
2002 Vision Fitness. All Rights Reserved. 8.02 Part #Z26RB60-AG1825PRD
AG18.25PRD
REV1
8
|