VT550 LCD Display
User Guide
Guide de l’utilisateur
Bedienungsanleitung
Guía del usuario
Guida dell’utente
Guia do Usuário
Användarhandbok
Käyttöopas
PodrĊcznik uĪytkownika
Full 15" Diagonal Viewable Screen
Copyright © ViewSonic Corporation, 2002. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of
ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC
are trademarks of VESA.
®
ENERGY STAR is a registered trademark of the U.S. Environmental Protection Agency (EPA).
®
As an ENERGY STAR partner, ViewSonic Corporation has determined that this product meets the
®
ENERGY STAR guidelines for energy efficiency.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this mate-
rial, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
change product specifications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available,
please register your product on the Internet at: www.viewsonic.com. The ViewSonic® Wizard CD-
ROM also provides an opportunity for you to print the registration form, which you may mail or fax
to ViewSonic.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
ViewSonic VT550
VLCDS23897-3W
A-CD-VT550-1
______________
______________
Product disposal at end of product life
ViewSonic is concerned about the preservation of our environment. Please dispose of this product
properly at the end of its useful life. Your local waste disposal company may provide information
about proper disposal.
ViewSonic
VT550
2
Getting Started
Congratulations on your purchase of a ViewSonic® LCD display.
Important!
avetheoriginalboxandallpackingmaterialorutureshippingneeds.
The word “Windows” in this user guide refers to the following Microsoft
NOTE:
operating systems: Windows ‘95, Windows NT, Windows ‘98, Windows 2000,
Windows Me (Millennium), and Windows XP.
Package Contents
Your LCD display package includes:
• LCD display
• Power cords
• Video cables (VGA and DVI)
• Audio cable (stereo mini jack)
• Microphone cable
• AC/DC adapter
• ViewSonic Wizard CD-ROM
The CD jacket contains the Quick Start Guide, and the CD includes the
NOTE:
User Guide PDF files and INF/ICM display optimization files. The INF file
ensures compatibility with Windows operating systems, and the ICM file (Image
Color Matching) ensures accurate on-screen colors. ViewSonicrecommends that
you install both files.
Precautions
• Sit at least 18" from your LCD display.
• Place your LCD display in a well-ventilated
area. Do not place anything on your LCD
display that prevents heat dissipation.
• Avoid touching the screen. Skin oils are
difficult to remove.
• Ensure the area around the LCD display is
clean and free of moisture.
• Never remove the rear cover. Your LCD
display contains high-voltage parts. You may
be seriously injured if you touch them.
• Do not place heavy objects on the LCD
display, video cable, or power cord.
• Avoid exposing your LCD display to direct
sunlight or another heat source. Orient your
LCD display away from direct sunlight to
reduce glare.
• If smoke, abnormal noise, or strange odor is
present, immediately switch the LCD display
off and call your dealer or ViewSonic. It is
dangerous to continue using the LCD display.
• Always handle your LCD display with care
when moving it.
ViewSonic
VT550
3
Quick Installation
1 Remove two rear panel covers
5 Wizard CD (continued)
(2) Follow the on-screen instructions.
2 Connect power cord and AC/DC
adapter
3 Connect video cable
6 Audio Installation (optional)
•
•
Speakers Connect the audio cable (lime-colored) to
the AUDIO OUT port of your computer’s sound
card, then to the LCD display’s AUDIO IN port
(see illustration below).
• Make sure both the LCD display and
computer are turned OFF
• Connect the video cable from the LCD
display to the computer
Microphone Connect the microphone cable (pink-
colored to the MIC IN port of your computer’s
sound card, then to the LCD display’s MIC OUT
Macintoshusers:Models older than G3
port. Plug an external microphone into the MIC IN
require a Macintosh adapter. Attach the
adapter to the computer and plug the video
cable into the adapter.
To order a ViewSonic® Macintosh adapter,
jack on the back of the LCD display. (See
illustration below.)
•
Headphones Plug headphones into the headphone
jack shown below.
7 Windows users: Set the timing
contact ViewSonic Customerupport.
mode (resolution and refresh
4 Turn ON LCD display and
rate)
computer
Example:1024 x 768 @ 60 Hz.
Turn ON the LCD display, then turn ON the
computer. This sequence (LCD display
before computer) is important.
For instructions on changing the resolution
and refresh rate, see the graphic card’s user
guide.
NOTE: Windows users may receive a
message asking them to install the INF file.
This is on the CD.
Installation is complete. Enjoy your new
ViewSonic LCD display.
To be best prepared for any future customer
5 Insert the ViewSonic Wizard CD
into the computer’s CD drive.
service needs: print this user guide and write
the serial number in “ForYourRecords”on
page 2. (See back of LCD display.)
Follow the on-screen instructions
If your computer does not have a CD-ROM
drive, see “Customer Support.”
You can register your product online at the
website for your region. See the Customer
Support table in this guide.
(1) Wait for the CD-ROM to auto-start.
The ViewSonic Wizard CD-ROM also
provides an opportunity for you to print the
registration form which you may mail or fax
to ViewSonic.
NOTE: If the CD-ROM does not auto-start:
double-click on the CD-ROM icon in the
Windows Explorer, then double-click on
viewsonic.exe.
DVI video IN (digital)
VGA video IN (analog)
Power IN
Audio IN
Headphone IN jack
Kensington
lock
Rear panel covers
MIC OUT (pink)
Computer
power
cord
External MIC IN (white)
AC outlet (wall socket)
Power cord and AC/DC adapter
ViewSonic
VT550
4
Installation of Wall Mount (Optional)
To obtain a wall-mounting kit, contact ViewSonic or your local dealer. Refer to
the instructions that come with the base mounting kit. To convert your LCD
display from a desk-mounted to a wall-mounted display, do the following:
Four screw holes with
rubber filler
Disconnect Power.
1
Lay the LCD display face down
on a towel or blanket. If you
remove the base for a wall mount,
the microphone in the base is
disconnected. But, you can leave
the base attached to the LCD
display with the wall mount.
Notice the four screw holes for
the wall mount on the back as
shown on the left. Remove the
rubber filler from each screw
hole.
2
Attach the mounting bracket
from the VESA compatible wall-
mounting kit (75 mm x 75 mm
distance).
3
4
Attach the LCD display to the
wall, following the instructions in
the wall-mounting kit.
ViewSonic
VT550
5
Using the LCD Display
Setting the Timing Mode
Setting the timing mode is important for maximizing the quality of the
screen image and minimizing eye strain. The timing mode consists of the
resolution (example 1024 x 768) and refresh rate (or vertical frequency;
example 75 Hz). After setting the timing mode, use the OnView® controls
to adjust the screen image.
For the best picture quality set your LCD display timing mode to:
VESA 1024 x 768 @ 60Hz.
To set the Timing Mode:
1 Set the resolution: Right-click on the Windows desktop > Properties >
Settings > set the resolution.
2 Set the refresh rate: See your graphic card's user guide for instructions.
WARNING: Do not set the graphics card in your computer to exceed the
maximum refresh rate of 75Hz; doing so may result in permanent damage to
your LCD display.
OSD and Power Lock Settings
You can lock the On Screen Displays (OSDs) and/or the power button to prevent
unwanted changes to the current image settings.
• OSD LOCK: Press and hold the [1] and [▲] buttons on the face of the
monitor for 10 seconds. The message ODLOCKwill then display briefly
indicating that the OSD image settings are now locked.
• OSD UNLOCK: Press and hold the [1] and [▲] buttons again for 10
seconds. The message ODUNLOCKwill then display briefly indicating
that the OSD image settings are now unlocked.
• POWER BUTTON LOCK: Press and hold [1] and the down arrow ▼ for 10
seconds. If the power button is pressed the message owerButtonLocked
will display for 5 seconds. With or without this setting, after a power failure,
your LCD display’s power will automatically turn ON when power is
restored.
• POWER BUTTON UNLOCK: Press and hold [1] and the down arrow ▼
again for 10 seconds.
ViewSonic
VT550
6
Adjusting the Screen Image
Use the buttons on the front control panel to display and adjust the OnView®
controls which display on the screen. The OnView controls are explained at the
top of the next page and are defined in “Main Menu Controls” on page 9.
Main Menu
With OnView controls
Front Control Panel
shown below in detail
Speaker
Speaker
Scrolls through menu options and
adjusts the displayed control.
Microphone
Also a shortcut to display the
Contrast adjustment control
screen.
Displays the Main Menu
or exits the control screen
and saves adjustments
Displays the control
screen for the highlighted
control.
Shortcut key: toggles
between two controls on
some screens: i.e.
Contrast/Brightness.
Shortcut key: toggles
between analog (VGA)
and digital (DVI) video
connections.
Decreases or
increases volume
Power light
Green = ON
Orange = Power
Saving
Temporarily silences
audio output
Power
On/Off
Shortcut key: Toggles between standard and high
brightness mode for viewing PC data or video.
ViewSonic
VT550
7
Do the following to adjust the screen image:
To display the Main Menu, press button [1].
1
NOTE: All OnView menus and adjustment screens disappear automatically
after about 30 seconds.
To select a control you want to adjust, press ▲ or ▼ to scroll up or down the
Main Menu.
2
After the control is selected, press button [2]. A control screen like the one
shown below appears.
3
The line at the
bottom of the
screen tells you
what you can do
next: Exit or select
the Brightness
control.
The ▼ down
arrow decreases,
▲ up arrow
increases
To adjust the control, press the up ▲ or down ▼ buttons.
4
5
To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:
• Adjust your computer's graphic card so that it outputs a video signal 1024 x
768 @ 60 Hz to the LCD display. (Look for instructions on “changing the
refresh rate” in your graphic card's user guide.)
• If necessary, make small adjustments using H POSITION and V POSITION
until the screen image is completely visible. (The black border around the
edge of the screen should barely touch the illuminated “active area” of the
LCD display.)
ViewSonic
VT550
8
Main Menu Controls
Adjust the menu items shown below by using the up ▲ and down ▼ buttons.
Control Explanation
automatically sizes, centers, and fine tunes
Auto Image Adjust
the video signal to eliminate waviness and distortion.
Press the [2] button to obtain a sharper image.
NOTE: Auto Image Adjust works with most common video
cards. If this function does not work on your LCD display, then
lower the video refresh rate to 60 Hz and set the resolution to its
pre-set value.
adjusts the difference between the image background
Contrast
(black level) and the foreground (white level).
adjusts background black level of the screen image.
Brightness
Input Select
Audio Menu
toggles between an analog and a digital signal.
increases or decreases the loudness of the audio output.
adjusts the proportion of sound coming from each
Volume
Balance
speaker.
adjusts the low (bass) frequency audio output.
Bass
adjusts the high (treble) frequency audio output.
Treble
temporarily silences audio output.
Mute
ViewSonic
VT550
9
ation
djust
provides several color adjustment modes: preset
peratures and RGB which allows you to adjust red (R),
), and blue (B) separately. The factory setting for this
s 6500K (6500 Kelvin).
Adds blue to the screen image for cooler white (used
fice settings with fluorescent lighting).
Adds red to the screen image for warmer white and
Adds green to the screen image for a darker color.
Adds blue and green to the screen image for a darker
or — Adjusts red (R), green (G), and blue (B)
y.
ct color (R, G or B) press button [2].
st selected color, press ▲ or ▼.
1
2
ImpIf you select RECALL from the Main Menu when
the pis set to a Preset Timing Mode, colors return to the
6500K ry preset.
displays the timing mode (video signal input)
Information
coming from the graphics card in your computer. See your
graphic card’s user guide for instructions on changing the
resolution and refresh rate (vertical frequency).
NOTE: VESA 1024 x 768 @ 60 Hz (recommended) means that
the resolution is 1024 x 768 and the refresh rate is 60 Hertz.
displays the Manual Image Adjust menu.
Manual Image Adjust
The
controls are explained below:
Manual Image Adjust
adjusts tht theht(y)/F1 1 Tf 12.6997 0 0 12.6997 143.3317 492
Horizontal Size
Control Explanation
adjusts the video input signal to the screen size other
Scaling
than 1024 x 768 @ 60 Hz using the following options.
1:1 adjusts the video signal so that the height and width of the
picture are the same.
adjusts the video signal to fill the screen.
Fill all
maintains the correct video signal proportions
Fill Aspect Ratio
for different resolutions.
displays the menu shown below.
Setup Menu
The
controls are explained below:
Setup Menu
allows you to choose the language used in the menus
Language
and control screens.
displays the Resolution Notice menu shown
Resolution Notice
below.
advises the optimal resolution to use.
Resolution Notice
allows you to move the on-screen display menus
OSD Position
and control screens.
sets the length of time an on-screen display
OSD Timeout
screen is displayed. For example, with a “15 second” setting, if
a control is not pushed within 15 seconds, the display screen
disappears.
allows you to turn the On-Screen-Display
OSD Background
background on or off.
ViewSonic
VT550
12
Control Explanation
Memory Recall
returns adjustments to the original factory
settings if the display is operating in a factory Preset Timing
Mode listed in this user guide.
Exception: This control does not affect changes made with the
User Color control.
ViewSonic
VT550
13
Other Information
Specifications
Type
15" (full 15" viewable diagonal area),
TFT (Thin Film Transistor), Active Matrix XGA LCD,
0.297 mm pixel pitch
LCD
Color Filter
Glass surface
RGB vertical stripe
Anti-Glare
Video Sync
RGB analog (0.7/1.0 Vp-p, 75 ohms)
DVI-D (TMDS, 100 Ohms)
Composite Sync, Separate Sync, Sync on Green
fh:30-62 kHz, fv:50-75 Hz
Input signal
Multimedia
Speakers
2 x 2 watts
Audio Input
Microphone
Headphone
3.5 mm stereo mini connector
3.5 mm internal and external
3.5 mm mini stero connector
PC
Up to 1024 x 768 Non-interlaced (NI)
Power Macintosh up to 1024 x 768
Compatibility
Resolution
Macintosh1
Recommended and
supported
1024 x 768 @ 60, 75 Hz NI
800 x 600 @ 60, 75 Hz NI
640 x 480 @ 60, 75 Hz NI
720 x 400 @ 70 Hz NI
HDTV support 720p 1280 x 720 @ 60 Hz
Voltage
100-240 VAC, 50/60 Hz (auto switch), 12V DC, 3.0A
Power
Full Scan
304.1 mm (H) x 228.1 mm (V)
12.0" (H) x 9.0" (V)
Display area
Temperature
Humidity
Altitude
32° F to + 104° F (0° C to + 40° C)
10% to 90% (no condensation)
To 10,000 feet
Operating
conditions
Temperature
Humidity
Altitude
-4° F to + 140° F (-20° C to + 60° C)
10% to 90% (no condensation)
To 40,000 feet
Storage
conditions
Physical
(LCD display only)
360.0 mm (W) x 139.5 mm (D) x 342.0 mm (H)
14.7" (W) x 5.5" (D) x 13.5" (H)
Dimensions
Net
4.0 kg (8.8 lb ) LCD display only
Weight
UL, FCC-B, c-UL, IC-B, CE, NEMKO, SEMKO, DEMKO,
FIMKO, TCO’99, PCT (BZ02), TUV/Ergo, BSMI, PSB,
CCEE, CB Report, ISO 13406-2, TUV/GS, VCCI, PCBC,
Regulations
®
TUV-S, EPA, NOM, C-Tick, GOST-R, ENERGY STAR
On
Active Off
Normal (green LED)
<3W (orange LED)
Power saving
modes
Preset Timing Mode (pre-adjusted to VESA® 1024 x 768 @ 60 Hz)
Warning: Do not set the graphics card in your computer to exceed these refresh rates; doing so may
result in permanent damage to the LCD display.
1 Macintosh computers older than G3 require a ViewSonic®, Macintosh adapter. To order an adapter,
contact ViewSonic.
ViewSonic
VT550
14
Troubleshooting
No power
• Make sure power button (or switch) is ON.
• Make sure A/C power cord is securely connected to the DC power supply and
the power supply is firmly connected to the LCD display.
• Plug another electrical device (like a radio) into the power outlet to verify that
the outlet is supplying proper voltage.
Power is ON but no screen image
• Make sure the video cable supplied with the LCD display is tightly secured to
the video output port on the back of the computer. If the other end of the
video cable is not attached permanently to the LCD display, tightly secure it
to the LCD display.
• Adjust brightness and contrast.
• If you are using an Macintosh older than G3, you need a Macintosh adapter.
Wrong or abnormal colors
• If any colors (red, green, or blue) are missing, check the video cable to make
sure it is securely connected. Loose or broken pins in the cable connector
could cause an improper connection.
• Connect the LCD display to another computer.
• If you have an older graphics card, contact ViewSonic for a non-DDC
adapter.
Control buttons do not work
• Press only one button at a time.
ViewSonic
VT550
15
Customer Support
For technical support or product service, see the table below or contact your
reseller.
You will need the product serial number.
NOTE:
Country/
Region
Web site
T = Telephone Email
F = FAX
United States
viewsonic.com/
support
T: (800) 688-6688
service.us@
F: (909) 468-1202 viewsonic.com
Canada
viewsonic.com/
support
T: (800) 688-6688
F: (909) 468-1202 service.ca@
viewsonic.com
United Kingdom
viewsoniceurope.com T: 0800 833 648
service.eu@
F: (01293) 643910 viewsoniceurope.com
Europe, Middle
East, Baltic
countries, and
North Africa
viewsoniceurope.com Contact your
reseller
service.eu@
viewsoniceurope.com
Australia and New viewsonic.com.au
Zealand
T: +61 2 9929 3955 service.au@
F: +61 2 9929 8393 viewsonic.com
Singapore/India
and Southeast
Asia
viewsonic.com.sg
T: 65 273 4018
F: 65 273 1566
service.sg@
viewsonic.com
Other Asia/Pacific viewsonic.com.tw
countries
T: 886 2 2246 3456 service.ap@
F: 886 2 8242 3668 viewsonic.com
South Africa
viewsonic.com/asia
T: 886 2 2246 3456 service.ap@
F: 886 2 8242 3668 viewsonic.com
ViewSonic
VT550
16
Cleaning the LCD Display
• MAKE SURE THE LCD DISPLAY IS TURNED OFF.
• NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE
SCREEN OR CASE.
To clean the screen:
Wipe the screen with a clean, soft, lint-free cloth. This removes dust and
other particles.
If still not clean, apply a small amount of non-ammonia, non-alcohol based
glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen.
1
2
To clean the case:
Use a soft, dry cloth.
1
2
If still not clean, apply a small amount of a non-ammonia, non-alcohol
based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then
wipe the surface.
Disclaimer
ViewSonic does not recommend the use of any ammonia or alcohol-based
cleaners on the LCD display screen or case. Some chemical cleaners have been
reported to damage the screen and/or case of the LCD display. ViewSonic will not
be liable for damage resulting from use of any ammonia or alcohol-based cleaners.
ViewSonic
VT550
17
Limited Warranty
VIEWSONIC LCD DISPLAY
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship during the
warranty period. If a product proves to be defective in material or workmanship during the warranty
period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement
product or parts may include remanufactured or refurbished parts or components.
How long the warranty is effective:
ViewSonic® LCD displays are warranted for three (3) years for all parts including the light source and
three (3) years for all labor from the date of the first consumer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
b. Repair or attempted repair by anyone not authorized by ViewSonic.
c. Any damage of the product due to shipment.
d. Removal or installation of the product.
e. Causes external to the product, such as electrical power fluctuations or failure.
f. Use of supplies or parts not meeting ViewSonic’s specifications.
g. Normal wear and tear.
h. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support.
You will need to provide your product's serial number.
2. To obtain service under warranty, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic ser-
vice center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact
ViewSonic.
Limitation of implied warranties:
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Exclusion of damages:
VIEWSONIC'S LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE
PRODUCT. VIEWSONIC SHALL NOT BE LIABLE FOR:
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES
BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF
PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH
BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of
incidental or consequential damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada,
contact ViewSonic or your local ViewSonic dealer.
ViewSonic LCD Display Warranty (V3.0)
Release Date: 01-29-2002
ViewSonic
VT550
18
Appendix
Safety Guidelines
Warning: This device must be operated with the original power supply, part number: 12V DC, ADP-50GH B.
CAUTION: The socket-outlet should be installed near the equipment and should be easily accessible.
CAUTION: Use a power cable that is properly grounded. Always use the appropriate AC cord that is
certified for the individual country. Some examples are listed below:
USA.................UL
Canada.............CSA
Germany..........VDE
Switzerland ..... SEV
Britain ............. BASE/BS
Japan ............... Electric Appliance Control Act
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The power cord set for this unit has been enclosed and has been selected according to the country of des-
tination and must be used to prevent electric shock. Use the following guidelines if it is necessary to replace
the original cord set, or if the cord set is not enclosed.
The female receptacle of the cord set must meet IEC-60320 requirements and may look like (Figure A1
below):
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA
Labeled. For units which are mounted on a desk or table, type SVT or SJT cord sets may be used. For
units which sit on the floor, only SJT type cord sets may be used. The cord set must be selected according
to the current rating for your unit. Please consult the table below for the selection criteria for power cords
used in the United States and Canada.
Cord Type
Size of Conductors in Cord
Maximum Current Rating of Unit
SJT
18 AWG
16 AWG
14 AWG
10 Amps
12 Amps
12 Amps
SVT
18 AWG
17 AWG
10 Amps
12 Amps
For European Countries
In Europe you must use a cord set which is appropriate for the receptacles in your country. The cord set is HAR-
Certified, and a special mark that will appear on the outer sheath, or on the insulation of one of the inner conductors.
AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET THEN THE PLUG SHOULD BE
CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO AN
APPROPRIATE SOCKET.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green-and-Yellow: Earth
Blue: Neutral
Brown: Live
If the coloured wires of the mains lead of this appliance do not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by
the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or
coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked
with the letter L or coloured RED.
If you have any questions concerning which proper power cord to use, please consult with the dealer from whom you
have purchased the product.
ViewSonic
VT550
19
Compliance Information for U.S.A.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Warning
To assure continued FCC compliance, the user must use grounded power supply cord and the provided
shielded video interface cable with bonded ferrite cores. If a BNC cable is going to be used, use only a
shielded BNC(5) cable. Also, any unauthorized changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this device.
CE Conformity for Europe
The device complies with the requirements of the EEC directive 89/336/EEC
as amended by 92/31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic
compatibility,” and 73/23/EEC as amended by 93/68/EEC Art.13 with regard
to “Safety.”
ViewSonic
VT550
20
ViewSonic Corporation
|