Package Contents:
1
3
1. Receiver
2. Antenna
3. Twin-lead wire, 6 feet
4. Manual
Wiring:
Preliminary Operator Tests:
1. Make sure door or gate
operator has been properly
installed in accordance with
unit’s installation instructions.
1. Disconnect power to the door
or gate operator before
proceeding.
P.O. Box 67 Mt. Hope, OH 44660
(888) 827-3667
Power
Supply
10V - 28V
AC/DC
PWR
NON-POLARIZED
PWR
WARNING: To prevent
electrical shock, be
sure electrical power is
disconnected before
proceeding with wiring.
2. Test and confirm proper
operation of the door or gate
operator before proceeding with
the installation of this receiver.
RLY
RLY
Door or Gate
control input
Optional Accessories:
1.
2.
1. Power Adapter
2. Antenna Extension Kit
WARNING: Keep
fingers and other body
parts away from all
moving parts of the
door and gate
operators system
while the system is
being operated.
Radio Receiver
2. Connect the enclosed twin-lead
wires to the terminals labeled
RLY. (use only 22 AWG or larger;
CL2X or better)
Models: 3990-372, 3994-433
Installation Instructions
3. Connect other end of twin-lead
wires to door or gate opener’s
control input.
and Owner’s Manual
Definition of Symbol
Warning
4. Connect power to the two
terminals labeled PWR. Receiver
requires 10V to 28V AC or DC.
WARNING: To prevent
unintended operation,
disconnect power to
the door or gate
Installation Safety Precautions
operator after
completing the above
preliminary operator
tests.
WARNING: INCORRECT INSTALLATION CAN LEAD
TO SEVERE OR FATAL INJURY. FOLLOW THESE
INSTRUCTIONS CAREFULLY.
4
READ and FOLLOW all installation instructions.
Connect Antenna:
2
1. Before installing this receiver, read the door or gate operator’s instruction
manual fully, so you are aware of all of the unit’s functions and features.
Direct Connect Antenna: Attach
antenna as shown. For best
reception keep antenna wire
straight and away from metal
objects.
Mounting:
2. Wear protective gloves to install, repair, or adjust door, gate, or operator
to avoid hand injuries.
WARNING: Do not
connect electrical
power to this receiver
until instructed to do
so.
3. Wear eye protection when using tools to install, repair, or adjust door,
gate, or operator to prevent eye injuries.
Antenna Extension Kit
(Optional):
Radio Receiver Specifications
Operating Temperature Range:.........................-22 F to 160 F
IP (Ingress Protection, International Protection):.... IP20
4. Mount control buttons within sight of door or gate, at a minimum height
of 5 ft, so small children cannot reach them. Keep control buttons away
from all moving parts of a door and at least 6 ft away from all moving
parts of a gate or its operator.
WARNING: Disconnect
electric power to door
or gate operator before
making repairs or
removing case
1. Connect extension wire to
receiver.
NOTICE: Dry Locations Only
2. Route wire outside metal
enclosure. Route and secure wire
away from moving parts.
INPUT POWER
Non-polarized input connection.
10 to 28 VDC, 40 mA with relay off, 60 mA with relay active
10 to 28 VAC, 40 mA with relay off, 90 mA with relay active
5. Before installing receiver, disconnect all power to door or gate operator
to prevent unintended operation.
covers.
3. Mount antenna holder outside
enclosure.
6. Do not connect this receiver to a power source until instructed to do so.
Do not reconnect power to the door or gate operator until instructed to
do so.
1. Select a location four to six feet
from other receivers. Receiver
can be attached to metal, wood,
or plastic surfaces.
NOTICE: Class 2 product, for voltages 32 VAC/DC or less
4. Screw antenna to extension
wire.
RELAY OUTPUT CONTACTS
7. Only install receiver on a properly functioning door or gate operator.
Normally-open, dry contacts, non-polarized connection.
Switching current capability:1.0 mA to 0.5 A at 10 to 28 VAC and 2.0 mA to
1.0 A at 10 to 28 VDC
2. Use screws or other fastening
NOTICE: Do not route coax wire
near any moving parts of the
operator. If necessary, secure
coax wire away from any moving
parts.
8. Installation and wiring must comply with local building and electrical
codes. This product is not intended and must not be installed in a explo-
sive environment.
means to attach receiver.
3. If receiver is mounted inside a
metal enclosure, use an antenna
extension kit (optional) to extend
the antenna outside of the
enclosure.
RF Center Frequency:.............................Model 3990-372, 372.5 MHz.
Model 3994-433, 433.92 MHz.
9. Pay close attention to all warnings, notices, and notes in these
instructions.
5. Position antenna wire straight.
For best reception, keep antenna
away from metal.
Antenna length:....................................... Model 3990-372, 7.2 inch
Model 3994-433, 5.8 inch
Capable of learning 14 transmitters (any combination of portable
transmitters, RF wall-stations or RF keypads).
10. To prevent electrical shock and/or fire hazards, do not connect this
receiver to any voltages greater than 32 VAC or DC.
WARNING: After installing and testing this receiver, test
all safety features of your door or gate’s operator.
Disconnect this receiver if any of your door or gate’s safety
system features fail to function properly. Then have your door
or gate operator serviced immediately by a qualified person.
IMPORTANT NOTICE!
Read the enclosed instructions carefully before installing this radio receiver.
Pay close attention to all warnings and notes. This manual should be
retained for future reference.
© Copyright 2007 Wayne-Dalton Corp.
Part No.318705
Rev 3 7/9/2007
You can reach us Toll Free 1-888-827-3667 for Consumer Assistance or online at www. wayne-dalton.com
|