4. Locate the single memory expansion slot in the open compartment. Notice the loca-
tion of the off-center key on the expansion slot. One expansion slot will be occupied with
the standard memory module.
VIKING MEMORY
INSTALLATION GUIDE
SONY®
VAIO PCG-808, PCG-812, PCG-818
5. To install a memory module, insert the
module into the expansion slot at an
angle and then push it down until it clicks
into place. To be certain that the module
is installed correctly, ensure that the off-
center notch on the module is aligned
with the off-center key of the expansion
slot. The module can only be installed
one way due to the position of the notch.
Manual No. 1005206
•
Release 04/99, Rev. D
®
S P E E D
•
P O W E R
•
P E R F O R M A N C E
The Sony VAIO PCG-808, PCG-812 and PCG-818 come standard with 64MB of memory
soldered. They can be expanded to a maximum of 192MB* by installing the following
Viking Components memory options into their one available expansion slot.
6. Replace the memory expansion cover and be sure to secure its two holding screws.
7. Replace the battery back into its compartment and turn the system right-side up.
8. Replace the AC power supply and any other cables you may have disconnected.
Description
Viking P/N
9. Open the display screen and turn the system on. The computer will automatically
reconfigure itself to recognize the newly added memory. The new memory can be veri-
fied during the POST routine at start-up and at the SETUP utility.
32MB SDRAM Memory Module
64MB SDRAM Memory Module
128MB SDRAM Memory Module
SNY732, RSNY732
SNY764, RSNY764
SNY7128, RSNY7128
The installation is now complete.
*Requires the removal of all standard memory.
WARRANTY & DISCLAIMERS:
All Viking Components products have been thoroughly tested free of defects in material and workman-
ship. If any malfunction should occur while using one of our products in its recommended environment,
Viking, at its option, will repair or replace the product at no charge, provided the product or any part there-
of has not been abused, misused, neglected, replaced, repaired or modified. Viking shall make the final
determination as to the existence and the cause of any defect. Viking will not repair or replace products
designated as having a“Limited Lifetime”which fail solely because their estimated life has expired. No war-
ranty is made with respect to customer products produced to original purchaser specifications except as
specifically stated in writing by Viking.
Caution:
Electro Static Discharge (ESD) can damage electronic components. Before touching the mem-
ory module, ensure that you are discharged of static electricity by touching a grounded metal
object.
All shipping costs shall be the responsibility of the purchaser.
Except as provided herein,there are no express or implied warranties of merchantability or fitness for a par-
ticular purpose. Under no circumstances will Viking Components be liable in any way to the purchaser for
any damages, including but not limited to lost revenue, lost wages, or any other incidental or consequen-
tial damages arising out of the use of or inability to use this product. Viking reserves the right to make
modifications in both hardware and software without prior notifications.
INSTALLATION INSTRUCTIONS:
1.Turn the computer off and disconnect the AC power supply and any other cables from
the unit.
Note: If the unit appears to be powered down, ensure that it is not in Suspend
mode.
All Viking Components are 100% guaranteed compatible with the OEM machines for which they are
designed. All OEM's names, trademarks and part numbers are used for identification purposes only, and in
no way imply that any of our products are original equipment parts.
2. Turn the computer upside-down. Remove the battery from the system. If you are not
Sony and VAIO are a registered trademarks of Sony Electronics Inc.
familiar with this procedure, please refer to your computer’s “Owner’s Manual.”
Product names mentioned herein may be trademarks or registered trademarks of their respective compa-
nies.
3. Locate the memory expansion cover on the right side of the bottom panel. Also locate
the two holding screws securing this cover to the bottom panel. Remove the screws with
a small Phillips screwdriver. Then remove cover by lifting it toward you.
Copyright 1999 Viking Components, Inc.
|