PJD5353
DLP Projector
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
YLHZVRQLFꢀFRPꢁLQꢁ(QJOLVKꢂꢁRUꢁLQꢁVSHFL¿FꢁODQJXDJHVꢁXVLQJꢁWKHꢁ5HJLRQDOꢁVHOHFWLRQꢁER[ꢁLQꢁ
the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente
las instrucciones en este manual”
Important Safety Instructions
1.
2.
Read these instructions.
Keep these instructions.
ꢅꢁꢀꢀ +HHGꢀDOOꢀZDUQLQJVꢁ
ꢇꢁꢀꢀ )ROORZꢀDOOꢀLQVWUXFWLRQVꢁ
ꢌꢁꢀꢀ 'RꢀQRWꢀXVHꢀWKLVꢀXQLWꢀQHDUꢀZDWHUꢁ
ꢊꢁꢀꢀ ꢀ&OHDQꢀZLWKꢀDꢀVRIWꢐꢀGU\ꢀFORWKꢁ
7.
ꢀ'RꢀQRWꢀEORFNꢀDQ\ꢀYHQWLODWLRQꢀRSHQLQJVꢁꢀ,QVWDOOꢀWKHꢀXQLWꢀLQꢀDFFRUGDQFHꢀZLWKꢀ
the manufacturer’s instructions.
ꢉꢁꢀꢀ ꢀ'RꢀQRWꢀLQVWDOOꢀQHDUꢀDQ\ꢀKHDWꢀVRXUFHVꢀVXFKꢀDVꢀUDGLDWRUVꢐꢀKHDWꢀUHJLVWHUVꢐꢀ
VWRYHVꢐꢀRUꢀRWKHUꢀGHYLFHVꢀꢍLQFOXGLQJꢀDPSOL¿HUVꢎꢀWKDWꢀSURGXFHꢀKHDWꢁ
ꢋꢁꢀꢀ ꢀ'RꢀQRWꢀGHIHDWꢀWKHꢀVDIHW\ꢀSXUSRVHꢀRIꢀWKHꢀSRODUL]HGꢀRUꢀJURXQGLQJꢃW\SHꢀ
SOXJꢁꢀ$ꢀSRODUL]HGꢀSOXJꢀKDVꢀWZRꢀEODGHVꢀZLWKꢀRQHꢀZLGHUꢀWKDQꢀWKHꢀRWKHUꢁꢀ
A grounding type plug has two blades and a third grounding prong.
The wide blade and the third prong are provided for your safety. If the
SURYLGHGꢀSOXJꢀGRHVꢀQRWꢀ¿WꢀLQWRꢀ\RXUꢀRXWOHWꢐꢀFRQVXOWꢀDQꢀHOHFWULFLDQꢀIRUꢀ
replacement of the obsolete outlet.
ꢈꢄꢁꢀꢀ ꢀ3URWHFWꢀWKHꢀSRZHUꢀFRUGꢀIURPꢀEHLQJꢀZDONHGꢀRQꢀRUꢀSLQFKHGꢀSDUWLFXODUO\ꢀDWꢀ
SOXJVꢁꢀ&RQYHQLHQFHꢀUHFHSWDFOHVꢀDQGꢀWKHꢀSRLQWꢀZKHUHꢀWKH\ꢀH[LWꢀIURPꢀWKHꢀ
unit. Be sure that the power outlet is located near the unit so that it is
easily accessible.
ꢈꢈꢁꢀꢀ ꢀ2QO\ꢀXVHꢀDWWDFKPHQWVꢂDFFHVVRULHVꢀVSHFL¿HGꢀE\ꢀWKHꢀPDQXIDFWXUHUꢁ
ꢈꢆꢁꢀꢀ ꢀ8VHꢀRQO\ꢀZLWKꢀWKHꢀFDUWꢐꢀVWDQGꢐꢀWULSRGꢐꢀEUDFNHWꢐꢀRUꢀWDEOHꢀVSHFL¿HGꢀ
by the manufacturer, or sold with the unit. When a cart is used,
XVHꢀFDXWLRQꢀZKHQꢀPRYLQJꢀWKHꢀFDUWꢂXQLWꢀFRPELQDWLRQꢀWRꢀDYRLGꢀ
injury from tipping over.
ꢈꢅꢁꢀꢀ ꢀ8QSOXJꢀWKLVꢀXQLWꢀZKHQꢀXQXVHGꢀIRUꢀORQJꢀSHULRGVꢀRIꢀWLPHꢁ
ꢈꢇꢁꢀꢀ ꢀ5HIHUꢀDOOꢀVHUYLFLQJꢀWRꢀTXDOL¿HGꢀVHUYLFHꢀSHUVRQQHOꢁꢀ6HUYLFLQJꢀLVꢀUHTXLUHGꢀ
ZKHQꢀWKHꢀXQLWꢀKDVꢀEHHQꢀGDPDJHGꢀLQꢀDQ\ꢀZD\ꢐꢀVXFKꢀDVꢑꢀLIꢀWKHꢀSRZHUꢃVXSSO\ꢀ
cord or plug is damaged, if liquid is spilled onto or objects fall into the
XQLWꢐꢀLIꢀWKHꢀXQLWꢀLVꢀH[SRVHGꢀWRꢀUDLQꢀRUꢀPRLVWXUHꢐꢀRUꢀLIꢀWKHꢀXQLWꢀGRHVꢀQRWꢀ
operate normally or has been dropped.
ii
Declaration of RoHS Compliance
7KLVꢀSURGXFWꢀKDVꢀEHHQꢀGHVLJQHGꢀDQGꢀPDQXIDFWXUHGꢀLQꢀFRPSOLDQFHꢀZLWKꢀ'LUHFWLYHꢀꢆꢄꢄꢆꢂꢋꢌꢂ
(&ꢀRIꢀWKHꢀ(XURSHDQꢀ3DUOLDPHQWꢀDQGꢀWKHꢀ&RXQFLOꢀRQꢀUHVWULFWLRQꢀRIꢀWKHꢀXVHꢀRIꢀFHUWDLQꢀ
KD]DUGRXVꢀVXEVWDQFHVꢀLQꢀHOHFWULFDOꢀDQGꢀHOHFWURQLFꢀHTXLSPHQWꢀꢍ5R+6ꢀ'LUHFWLYHꢎꢀDQGꢀLVꢀ
GHHPHGꢀWRꢀFRPSO\ꢀZLWKꢀWKHꢀPD[LPXPꢀFRQFHQWUDWLRQꢀYDOXHVꢀLVVXHGꢀE\ꢀWKHꢀ(XURSHDQꢀ
Technical Adaptation Committee (TAC) as shown below:
Proposed
Maximum
Substance
Actual Concentration
Concentration
/HDGꢀꢍ3Eꢎ
ꢄꢁꢈꢏ
ꢄꢁꢈꢏ
ꢄꢁꢄꢈꢏ
ꢄꢁꢈꢏ
ꢄꢁꢈꢏ
ꢒꢀꢄꢁꢈꢏ
ꢒꢀꢄꢁꢈꢏ
ꢒꢀꢄꢁꢄꢈꢏ
ꢒꢀꢄꢁꢈꢏ
ꢒꢀꢄꢁꢈꢏ
0HUFXU\ꢀꢍ+Jꢎ
Cadmium (Cd)
ꢊꢓ
+H[DYDOHQWꢀ&KURPLXPꢀꢍ&U
)
Polybrominated biphenyls (PBB)
Polybrominated diphenyl ethers
ꢍ3%'(ꢎ
ꢄꢁꢈꢏ
ꢒꢀꢄꢁꢈꢏ
&HUWDLQꢀFRPSRQHQWVꢀRIꢀSURGXFWVꢀDVꢀVWDWHGꢀDERYHꢀDUHꢀH[HPSWHGꢀXQGHUꢀWKHꢀ$QQH[ꢀRIꢀWKHꢀ
5R+6ꢀ'LUHFWLYHVꢀDVꢀQRWHGꢀEHORZꢑ
([DPSOHVꢀRIꢀH[HPSWHGꢀFRPSRQHQWVꢀDUHꢑ
ꢈꢁꢀꢀ0HUFXU\ꢀLQꢀFRPSDFWꢀÀXRUHVFHQWꢀODPSVꢀQRWꢀH[FHHGLQJꢀꢌꢀPJꢀSHUꢀODPSꢀDQGꢀLQꢀRWKHUꢀ
ODPSVꢀQRWꢀVSHFL¿FDOO\ꢀPHQWLRQHGꢀLQꢀWKHꢀ$QQH[ꢀRIꢀ5R+6ꢀ'LUHFWLYHꢁ
ꢆꢁꢀꢀ/HDGꢀLQꢀJODVVꢀRIꢀFDWKRGHꢀUD\ꢀWXEHVꢐꢀHOHFWURQLFꢀFRPSRQHQWVꢐꢀÀXRUHVFHQWꢀWXEHVꢐꢀDQGꢀ
HOHFWURQLFꢀFHUDPLFꢀSDUWVꢀꢍHꢁJꢁꢀSLH]RHOHFWURQLFꢀGHYLFHVꢎꢁ
ꢅꢁꢀꢀ/HDGꢀLQꢀKLJKꢀWHPSHUDWXUHꢀW\SHꢀVROGHUVꢀꢍLꢁHꢁꢀOHDGꢃEDVHGꢀDOOR\VꢀFRQWDLQLQJꢀꢉꢌꢏꢀE\ꢀZHLJKWꢀ
or more lead).
ꢇꢁꢀꢀ/HDGꢀDVꢀDQꢀDOORWWLQJꢀHOHPHQWꢀLQꢀVWHHOꢀFRQWDLQLQJꢀXSꢀWRꢀꢄꢁꢅꢌꢏꢀOHDGꢀE\ꢀZHLJKWꢐꢀDOXPLQLXPꢀ
FRQWDLQLQJꢀXSꢀWRꢀꢄꢁꢇꢏꢀOHDGꢀE\ꢀZHLJKWꢀDQGꢀDVꢀDꢀFRRSHUꢀDOOR\ꢀFRQWDLQLQJꢀXSꢀWRꢀꢇꢏꢀOHDGꢀE\ꢀ
weight.
1
Copyright Information
©
®
Copyright ꢀ9LHZ6RQLF ꢀ&RUSRUDWLRQꢐꢀꢆꢄꢈꢈꢁꢀ$OOꢀULJKWVꢀUHVHUYHGꢁ
0DFLQWRVKꢀDQGꢀ3RZHUꢀ0DFLQWRVKꢀDUHꢀUHJLVWHUHGꢀWUDGHPDUNVꢀRIꢀ$SSOHꢀ,QFꢁ
0LFURVRIWꢐꢀ:LQGRZVꢐꢀ:LQGRZVꢀ17ꢐꢀDQGꢀWKHꢀ:LQGRZVꢀORJRꢀDUHꢀUHJLVWHUHGꢀWUDGHPDUNVꢀRIꢀ
0LFURVRIWꢀ&RUSRUDWLRQꢀLQꢀWKHꢀ8QLWHGꢀ6WDWHVꢀDQGꢀRWKHUꢀFRXQWULHVꢁ
9LHZ6RQLFꢐꢀWKHꢀWKUHHꢀELUGVꢀORJRꢐꢀ2Q9LHZꢐꢀ9LHZ0DWFKꢐꢀDQGꢀ9LHZ0HWHUꢀDUHꢀUHJLVWHUHGꢀ
WUDGHPDUNVꢀRIꢀ9LHZ6RQLFꢀ&RUSRUDWLRQꢁ
9(6$ꢀLVꢀDꢀUHJLVWHUHGꢀWUDGHPDUNꢀRIꢀWKHꢀ9LGHRꢀ(OHFWURQLFVꢀ6WDQGDUGVꢀ$VVRFLDWLRQꢁꢀ'306ꢀDQGꢀ
''&ꢀDUHꢀWUDGHPDUNVꢀRIꢀ9(6$ꢁ
36ꢂꢆꢐꢀ 9*$ꢀDQGꢀ;*$ꢀDUHꢀUHJLVWHUHGꢀWUDGHPDUNVꢀRIꢀ,QWHUQDWLRQDOꢀ%XVLQHVVꢀ0DFKLQHVꢀ
Corporation.
'LVFODLPHUꢑꢀ9LHZ6RQLFꢀ&RUSRUDWLRQꢀVKDOOꢀQRWꢀEHꢀOLDEOHꢀIRUꢀWHFKQLFDOꢀRUꢀHGLWRULDOꢀHUURUVꢀRUꢀ
omissions contained herein; nor for incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.
,QꢀWKHꢀLQWHUHVWꢀRIꢀFRQWLQXLQJꢀSURGXFWꢀLPSURYHPHQWꢐꢀ9LHZ6RQLFꢀ&RUSRUDWLRQꢀUHVHUYHVꢀWKHꢀ
ULJKWꢀWRꢀFKDQJHꢀSURGXFWꢀVSHFL¿FDWLRQVꢀZLWKRXWꢀQRWLFHꢁꢀ,QIRUPDWLRQꢀLQꢀWKLVꢀGRFXPHQWꢀPD\ꢀ
change without notice.
1RꢀSDUWꢀRIꢀWKLVꢀGRFXPHQWꢀPD\ꢀEHꢀFRSLHGꢐꢀUHSURGXFHGꢐꢀRUꢀWUDQVPLWWHGꢀE\ꢀDQ\ꢀPHDQVꢐꢀIRUꢀDQ\ꢀ
SXUSRVHꢀZLWKRXWꢀSULRUꢀZULWWHQꢀSHUPLVVLRQꢀIURPꢀ9LHZ6RQLFꢀ&RUSRUDWLRQꢁ
Product Registration
To meet your future needs, and to receive any additional product information as it becomes
9LHZ6RQLF®ꢀ:L]DUGꢀ&'ꢃ520ꢀDOVRꢀSURYLGHVꢀDQꢀRSSRUWXQLW\ꢀIRUꢀ\RXꢀWRꢀSULQWꢀWKHꢀUHJLVWUDWLRQꢀ
IRUPꢐꢀZKLFKꢀ\RXꢀPD\ꢀPDLOꢀRUꢀID[ꢀWRꢀ9LHZ6RQLFꢁ
For Your Records
Product Name:
Model Number:
PJD5353
ViewSonic DLP Projector
VS14116
Document Number: PJD5353_UG_ENG Rev. 1A 05-23-11
Serial Number:
Purchase Date:
_______________________________
_______________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the
environment. Please use care and dispose of in accordance with local, state or federal laws.
9LHZ6RQLFꢀUHVSHFWVꢀWKHꢀHQYLURQPHQWꢀDQGꢀLVꢀFRPPLWWHGꢀWRꢀZRUNLQJꢀDQGꢀOLYLQJꢀJUHHQꢁꢀ7KDQNꢀ
\RXꢀIRUꢀEHLQJꢀSDUWꢀRIꢀ6PDUWHUꢐꢀ*UHHQHUꢀ&RPSXWLQJꢁꢀ3OHDVHꢀYLVLWꢀ9LHZ6RQLFꢀZHEVLWHꢀWRꢀOHDUQꢀ
more.
86$ꢀ ꢀ&DQDGDꢑꢀKWWSꢑꢂꢂZZZꢁYLHZVRQLFꢁFRPꢂFRPSDQ\ꢂJUHHQꢂUHF\FOHꢃSURJUDPꢂ
(XURSHꢑꢀKWWSꢑꢂꢂZZZꢁYLHZVRQLFHXURSHꢁFRPꢂXNꢂVXSSRUWꢂUHF\FOLQJꢃLQIRUPDWLRQꢂ
7DLZDQꢑꢀKWWSꢑꢂꢂUHF\FOHꢁHSDꢁJRYꢁWZꢂUHF\FOHꢂLQGH[ꢆꢁDVS[
2
Notes on the AC Power Cord
AC Power Cord must meet the requirement of countries where you use this projector.
Please confirm your AC plug type with the graphics below and ensure that the proper
AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet,
please contact your sales dealer. This projector is equipped with a grounding type AC
line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose
of this grounding type plug. We highly recommend using a video source device also
equipped with a grounding type AC line plug to prevent signal interference due to
voltage fluctuations.
Ground
EN-3
3
CONTENTS
Introduction ........................................................................5
Projector Features .......................................................................................................5
Package Contents .......................................................................................................6
Projector Overview ......................................................................................................7
Using the Product ..............................................................9
Control Panel ..............................................................................................................9
Connection Ports .......................................................................................................10
Remote Control .........................................................................................................11
Installing the Batteries ...............................................................................................13
Remote Control Operation ........................................................................................14
Connection .......................................................................15
Connecting a computer or monitor ............................................................................16
Connecting Video source devices .............................................................................17
Operation ..........................................................................20
Powering On/Off the Projector ..................................................................................20
Adjusting the Projector Height ...................................................................................21
Adjusting the Projector Focus ...................................................................................21
Adjusting Projection Image Size ...............................................................................22
Locking control keys ..................................................................................................23
Setting the presentation timer ...................................................................................24
Menu Operation ........................................................................................................25
Maintenance .....................................................................32
Cleaning the Lens .....................................................................................................32
Cleaning the Projector Housing ................................................................................32
Replacing the Lamp ..................................................................................................33
Specifications ...................................................................35
Dimensions ...............................................................................................................36
Ceiling mount installation ..........................................................................................36
Appendix ...........................................................................37
LED Indicator Messages ...........................................................................................37
Compatibility Modes ..................................................................................................38
Troubleshooting ........................................................................................................40
RS-232 Command and Configuration .......................................................................41
IR Control Code ........................................................................................................44
4
4
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user - friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
„
„
„
„
„
„
„
„
„
„
Single chip 0.55" Texas Instruments DLP® technology
XGA (1024 x 768 pixels)
Compatibility with Macintosh® computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display
Advanced electronic keystone correction
RS-232 connector for serial control
Less than 1 W power consumption in standby mode
HDMI compatibility
„
„
The information in this manual is subject to change without notices.
The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
N5
5
Package Contents
When you unpack the projector, make sure you have all these components:
Projector
AC Power Cord
Remote Control (IR) & batteries
(AAA *2 PCS)
VGA Cable (D-SUB to D-
ViewSonic CD Wizard
Quick Start Guide
SUB)
„
„
Contact you dealer immediately if any items are missing, appear damaged, or if
the unit does not work
Save the original shipping carton and Packing material; they will come-in handy
if you ever to ship your unit. for maximum protection, repack your unit as it was
originally packed at the factory.
.
EN-6
6
Projector Overview
Front View
8
7
6
1
2
3
4
5
Front IR remote control sensor
Elevator foot
Control panel
Focus ring
1
2
3
4
5
6
7
8
Projection lens
Lamp cover
Speaker
Ventilation holes
N7
7
Rear View
2
3
1
Connection ports
AC power socket
Kensington lock
1
2
3
Bottom View
3
1
3
2
Security bar
1
Ceiling mount holes
Ventilation holes
2
3
„
„
This projector can be used with a ceiling mount for support. The ceiling mount is
not included in the package.
Contact your dealer for information to mount the projector on a ceiling.
EN-8
8
Using the Product
Control Panel
1
2
3
4
6
5
7
8
POWER
MENU/
EXIT
TEMP/LAMP
4
Power
1
2
3
4
5
Turn the projector on or off.
SOURCE
Display the source selection bar.
MENU/EXIT
Display or exit the on-screen display menus.
Keystone/Arrow keys ( /Up, /Down)
Manually correct distorted images resulting from an angled projection.
Four directional buttons
Use four directional buttons to select items or make adjustments to your
selection.
MODE
6
Change the color mode setting by sequence.
POWER (Power LED indicator)
7
8
Refer to “LED Indicator Messages”.
TEMP/LAMP (Temp/Lamp LED indicator)
Refer to “LED Indicator Messages”.
N9
9
Connection Ports
3
9
1
2
4
8
6
5
7
10
AUDIO IN
1
2
3
4
5
Connect an audio output from video equipment or computer to this jack.
HDMI
Connect HDMI output from video equipment to this jack.
S-VIDEO
Connect S-Video output from video equipment to this jack.
COMPUTER IN 1
Connect image input signal (analog RGB or component) to this jack.
RS-232
When operating the projector via a computer, connect this to the controlling
computer's RS-232C port.
MINI USB
6
7
8
This connector is for firmware update and mouse function support.
COMPUTER OUT
Connect to a computer display, etc.
COMPUTER IN 2
Connect image input signal (analog RGB or component) to this jack.
VIDEO
9
Connect composite video output from video equipment to this jack.
AUDIO OUT
10
Connect to a speaker or other audio input equipment.
EN-10
10
Remote Control
Power
1
Turn the projector on or off.
13
14
15
16
17
VGA1
2
Display COMPUTER IN 1 signal.
Menu/ Left mouse
3
Display on-screen display menus.
Perform the left button of the
mouse when mouse mode is
activated.
3
4
5
6
18
19
Mouse/ Right mouse
4
Switch between the normal and
mouse modes.
5
Perform the right button of the
mouse when mouse mode is
activated.
7
8
9
10
11
12
20
21
Keystone/Arrow keys ( /Up,
5
6
/Down)
Manually correct distorted images
resulting from an angled
projection.
22
23
Left
When the On-Screen Display
(OSD) menu is activated, the #5,
#6, and #19 keys are used as
directional arrows to select the
desired menu items and to make
adjustments.
Color Mode
11
12
Select the picture setup mode.
Blank
Timer
Hide the screen picture.
7
8
Activate P-Timer OSD menu.
My Button
Source
13
14
User definable key for customized
function.
Display the source selection bar.
Auto
Pattern
9
Automatically determines the best
Display embedded test pattern.
picture timings for the displayed image.
Freeze
10
Freeze the projected image.
1
11
Video/Page Up
15
Using the remote mouse control
Switch input source to Composite/
S-Video/HDMI by sequence.
Perform page up function when
mouse mode is activated.
The capability of operating your computer
with the remote control gives you more
flexibility when delivering presentations.
1.
Connect the projector to your PC or
notebook with a USB cable prior to
using the remote control in place of
your computer’s mouse. See
“Connecting a computer” on page 16
for details.
VGA2
16
17
Display COMPUTER IN 2 signal.
ESC/Page Down
Goes back to previous OSD menu.
Perform page down function when
mouse mode is activated.
2.
3.
Set the input signal to COMPUTER IN
Enter
18
Confirmed selections.
1
or COMPUTER IN 2.
Press Mouse on the remote control to
switch from the normal mode to the
mouse mode. An icon appears on the
screen to indicate the activation of the
mouse mode.
Perform the desired mouse controls on
your remote control.
Right/ Lock
19
20
Activate panel key lock.
Magnify
Magnifies or reduces the projected
picture size.
Volume
21
22
23
4.
Adjust the volume level.
Mute
„
To move the cursor on the screen,
Cut off the sound temporarily.
press
/
/
/
.
Aspect
„
„
„
To left-click, press
To right-click, press
To drag-and-drop, press and hold
.
Select the display aspect ratio.
.
Enter, press to
/
/
/
drag. When it is where you want it,
press Enter again.
„
„
To operate your display software
program (on a connected PC)
which responds to page up/down
commands (like Microsoft
PowerPoint), press Page Up/Page
Down.
To return to the normal mode,
press Mouse again or other keys
except for the mouse related multi-
function keys.
EN-12
12
Installing the Batteries
1.
2.
3.
Open the battery cover in the
direction shown.
Install batteries as indicated by the
diagram inside the compartment.
Close the battery cover into
position.
Caution
„ Risk of explosion if battery is replaced by an incorrect type.
„ Dispose of used batteries according to the instructions.
„
Make sure the plus and minus terminals are correctly aligned when loading a battery.
„
Keep the batteries out of the reach of children. There is a danger of death by
accidentally swallowing the batteries.
„
„
Remove batteries from remote control when not using for extended periods.
Do not dispose of the used batteries along with household waste. Dispose of used
batteries according to local regulations.
„
„
„
Danger of explosion may happen if batteries are incorrectly replaced. Replce all
the batteries with new ones.
Batteries should not be in or near to fire or water, keep batteries in a dark, cool
and dry place.
If suspect battery leakage, wipe out the leakage and then replace new batteries.
If the leakage adheres to your body or clothes, rinse well with water immediately.
1
13
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
„
Operating the projector from
the front
„
The remote control may not operate when there is sunlight or other strong
light such as a fluorescent lamp shining on the remote sensor.
Operate the remote control from a position where the remote sensor is visible.
Do not drop the remote control or jolt it.
„
„
„
Keep the remote control out of locations with excessively high temperature or
humidity.
„
„
Do not get water on the remote control or place wet objects on it.
Do not disassemble the remote control.
EN-14
14
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
6
7
6
1
8
3
4
2
1
1
5
Audio cable
HDMI cable
VGA (D-Sub) to HDTV (RCA) cable
VGA cable (D-Sub to D-Sub)
USB cable
1
5
2
3
4
6
7
Composite Video cable
S-Video cable
VGA to DVI-A cable
8
Important
„ In the connections shown above, some cables may not be included with the
projector (see “Package Contents” on page 6). They are commercially
available from electronics stores.
„ The connection illustrations above are for reference only. The rear
connecting jacks available on the projector vary with each projector model.
„ For detailed connection methods, see pages 16-19.
1
15
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both!
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are!
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1.
Take the supplied VGA cable and connect one end to the D-Sub output socket of
the computer.
2.
Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
Important
„ Many notebooks do not turn on their external video ports when connected to
a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the
external display on/off. Locate a function key labeled CRT/LCD or a function
key with a monitor symbol on the notebook. Press FN and the labeled
function key simultaneously. Refer to your notebook's documentation to find
your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen,
you can connect the COMPUTER OUT signal output socket on the projector to an
external monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1.
Connect the projector to a computer as described in “Connecting a computer” on
page 16.
2.
Take a suitable VGA cable (only one supplied) and connect one end of the cable
to the!D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
Connect the other end of the cable to the COMPUTER OUT socket on the
projector.
3.
Important
„ The COMPUTER OUT output only works when COMPUTER IN 1 or
COMPUTER IN 2 is made to the projector.
EN-16
16
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one
of the following output sockets:
„
„
„
„
HDMI
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the
above!connecting methods, however each provides a different level of video quality.
The method!you choose will most likely depend upon the availability of matching
terminals on both the!projector and the Video source device as described below:
Terminal name
Terminal appearance
Reference
Picture quality
HDMI
“Connecting an HDMI
source device” on
page 17
HDMI
Best
COMPUTER
“Connecting a
Component Video
source device” on
page 18
Component Video
S-Video
Better
Good
S-VIDEO
VIDEO
“Connecting an S-
Video source device”
on page 18
“Connecting a
composite Video
source device” on
page 19
Video
Normal
Connecting an HDMI source device
Examine your Video source device to determine if it has a set of unused HDMI output
jacks available:
„
„
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the
device.
To connect the projector to an HDMI source device:
1.
Take an HDMI cable and connect one end to the HDMI output jack of the HDMI
source device.
2.
Connect the other end of the HDMI cable to the HDMI jack on the projector.
1
17
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component
Video output sockets available:
„
„
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the
device.
To connect the projector to a Component Video source device:
1.
Take a VGA (D-Sub) to HDTV (RCA) cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device.
Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
2.
Connect the other end of the cable (with a D-Sub type connector) to the
COMPUTER IN 1 or COMPUTER IN 2 socket on the projector.
Important
„ If the selected video image is not displayed after the projector is turned on
and the correct video source has been selected, check that the Video source
device is turned on and operating correctly. Also check that the signal cables
have been connected correctly.
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output
socket available:
„
„
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the
device.
To connect the projector to an S-Video source device:
1.
Take an S-Video cable and connect one end to the S-Video output socket of the
Video source device.
2.
Connect the other end of the S-Video cable to the S-VIDEO socket on the
projector.
Important
„ If the selected video image is not displayed after the projector is turned on
and the correct video source has been selected, check that the Video source
device is turned on and operating correctly. Also check that the signal cables
have been connected correctly.
„ If you have already made a Component Video connection between the
projector and this S-Video source device using Component Video
connections, you need not connect to this device using an S-Video
connection as this makes an unnecessary second connection of poorer
picture quality. See “Connecting Video source devices” on page 17 for
details.
EN-18
18
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite
Video output sockets available:
„
„
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the
device.
To connect the projector to a composite Video source device:
1.
Take a Video cable and connect one end to the composite Video output socket of
the Video source device.
Connect the other end of the Video cable to the VIDEO socket on the projector.
Important
!
2.
„ If the selected video image is not displayed after the projector is turned on
and the correct video source has been selected, check that the Video source
device is turned on and operating correctly. Also check that the signal cables
have been connected correctly.
„ You need only connect to this device using a composite Video connection if
Component Video and S-Video inputs are unavailable for use. See
“Connecting Video source devices” on page 17 for details.
1
19
Operation
Powering On/Off the Projector
Powering On the Projector:
1.
2.
Complete the AC power cord and peripheral signal cable(s) connections.
Press to turn on the projector.
The projector takes a minute or so to warm up.
Turn on your source (computer, notebook, DVD, etc.). The projector
automatically detects your source.
3.
„
If you are connecting multiple sources to the projector simultaneously, press
SOURCE on the projector or Source on the remote control to select your
desired signal or press your desired signal key on the remote control.
Warning
„ Never look into the lens when the lamp is on. This can damage your eyes.
„ This focal point concentrates high temperature. Do not place any object near
it to avoid possible fire hazard.
Powering Off the Projector:
1.
Press
Press Power again" appear on the screen.
Press again to confirm.
to turn off the projector lamp. You will see a message "Power off?
2.
„
„
The cooling fans continue to operate for cooling cycle.
When green mode is turned off, the Power LED begins flashing and the
projector has entered stand-by mode.
„
„
When green mode is turned o
projector has entered stand-by mode.
If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in stand-
n
,
the Power LED becomes steady light and the
by mode, simply press
to restart the projector.
3.
4.
Disconnect the AC power cord from the electrical outlet and the projector.
Do not turn on the projector right after power off.
EN-20
20
Adjusting the Projector Height
Elevator foot
The projector is equipped with an elevator foot to adjust the image height. To raise or
lower the image, turn the elevator foot to fine-tune the height.
„
To avoid damaging the projector, make sure that the elevator foot is fully
retracted before placing the projector in its carrying case.
Adjusting the Projector Focus
Focus ring
Focus the image by rotating the focus ring. A still image is recommended for focusing.
2
21
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
Screen
Center of lens
Projection distance
4 : 3 Screen
Vertical offset
Screen size
Diagonal
Projection
Image height Image width
Vertical offset
[inch (cm)]
3.6 (9)
[inch (cm)]
distance [inch (m)] [inch (cm)]
[inch (cm)]
32 (81)
40 (102)
60 (152)
80 (203)
100 (254)
150 (381)
200 (508)
250 (635)
300 (762)
22 (0.5)
33 (0.8)
44 (1.1)
55 (1.4)
83 (2.1)
111 (2.8)
139 (3.5)
167 (4.3)
24 (61)
36 (91)
48 (122)
5.4 (14)
7.2 (18)
9.0 (23)
13.4 (34)
17.9 (45)
22.4 (57)
26.9 (68)
48 (122)
60 (152)
90 (229)
120 (305)
150 (381)
180 (457)
64 (163)
80 (203)
120 (305)
160 (406)
200 (508)
240 (610)
„
Position the projector in a horizontal position; other positions can cause heat
build-up and damage to the projector.
„
„
Keep a space of 30 cm or more between the sides of the projector.
Do not use the projector in a smoky environment. Smoke residue may build-
up on critical parts and damage the projector or its performance/
Consult with your dealer for special installation such as suspending from a
ceiling.
„
EN-22
22
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings
from being changed accidentally (by children, for example). When the Panel Key
Lock is on, no control keys on the projector will operate except
Power.
1.
2.
Press
on the remote control.
A confirmation message is displayed. Select Yes to
confirm.
To release panel key lock:
1.
2.
Press
on the remote control.
A confirmation message is displayed. Select Yes to
confirm.
Important
„ If you press
Power to turn off the projector without disabling panel key
lock, the projector will still be in locked status the next time it is turned on.
2
23
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you
achieve better time management when giving presentations. Follow these steps to
utilize this function:
1.
Go to the Option > Presentation Timer menu and press
on the projector or
Enter on the remote control to display the Presentation Timer page.
2.
Highlight Timer Period and decide the timer period by pressing
Important
/
.
„ If the timer is already on, the timer will restart whenever the Timer Period is
reset.
Press
on the screen by pressing
3.
to highlight Display Timer and choose if you want the timer to show up
/
.
Selection
Always
Description
Displays the timer on screen throughout the presentation
time.
1 Min/2 Min/3 Min Displays the timer on screen in the last 1/2/3 minute(s).
Never
Hides the timer throughout the presentation time.
4.
5.
Press
to highlight Timer Position and set the timer position by pressing
/
.
Top-Left Ш Bottom-Left Ш Top-Right Ш Bottom-Right
Press to highlight Timer Counting Direction and select your desired
counting direction by pressing
/
.
Selection
Count Up
Count Down
Description
Increases from 0 to the preset time.
Decrease from the preset time to 0.
6.
7.
To activate the presentation timer, press
to highlight Start Counting and press
on the projector or Enter on the remote control
.
A confirmation message displays. Highlight Yes and press
on the projector or
Enter on the remote control to confirm.
EN-24
24
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings.
2
25
EN-26
26
How to operate
1.
Press MENU on the projector or Menu on the remote control to open the OSD
menu.
2.
3.
When OSD is displayed, use
/
to select any feature in the main menu.
After selecting the desired main menu item, press
feature setting.
to enter sub-menu for
4.
5.
Use
/
to select the desired item and adjust the settings with
/
.
Press MENU on the projector or Menu on the remote control, the screen will
return to the main menu.
6.
To exit OSD, Press MENU on the projector or Menu on the remote control again.
The OSD menu will close and the projector will automatically save the new
settings.
Picture
Color Mode
There are many factory presets optimized for various types of images.
„
„
„
„
„
„
„
„
„
Brightest
PC
Movie
ViewMatch
User 1
User 2
:
:
:
:
:
:
For the brightest environment.
For computer or notebook.
For home theater.
For accuracy color performance.
Memorize user 1 defined settings.
Memorize user 2 defined settings.
White board : For white projection screen type.
Black board : For black projection screen type.
Green board: For green projection screen type.
Reference Mode
Select a picture mode that best suits your need for the image quality and further fine-
tune the image. This function is only available when User 1 or User 2 is selected.
„
„
„
„
PC
Movie
ViewMatch
Brightest
:
:
:
:
For computer or notebook.
For home theater.
For accuracy color performance.
For the brightest environment.
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, then you can change the
intensity of each of 3 color (Red, Green, Blue) to customize user color temperature.
2
27
User Color
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select
each color, you can independently adjust its range, hue, saturation and gain according
to your preference.
White Intensity
Increase the brightness of white areas.
Gamma
Effect the represent of dark scenery. With greater gamma value, dark scenery will look
brighter.
Aspect Ratio
Select how the picture fits on the screen:
„
„
„
Auto : Scales an image proportionally to fit the projector's native resolution in its
horizontal or vertical width.
4:3
:
Scales an image so that it is displayed in the center of the screen with a
4:3 aspect ratio.
16:9 : Scales an image so that it is displayed in the center of the screen with a
16:9 aspect ratio.
Keystone
Manually correct distorted images resulting from an angled projection.
3D Sync
„
„
On: Enable 3D function.
Off: Disable 3D function.
3D Sync Invert (for TI 3D DLP-LINK only)
„
„
On: Invert left and right frame contents.
Off: Default frame contents.
Video/Audio
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Zoom
Zoom in and out the images.
Video Setting
EN-28
28
Allow you to enter the Video Setting menu.
„
„
„
Sharpness: Sharpen or soften the image.
Tint: Shift colors toward red or green.
Hue: Increase in the range will include colors consisted of more proportions of its
two adjacent colors.
Audio Setting
Allow you to enter the Audio Setting menu.
„
„
Volume: Adjust the projector’s volume level.
Mute: Cut off the sound temporarily.
Setting
Projector Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Menu Setting
Allow you to enter the Menu Setting menu.
„
„
Menu Position: Choose the menu location on the display screen.
Menu Display Time: Duration of OSD menu display countly starts (at idle state by
second).
„
OSD Transparency: Select to change the transparency level of the OSD
background.
Signal Type
Specify the source to the COMPUTER IN 1/COMPUTER IN 2 terminal that you wish to
project.
„
Auto : Automatically detect the input signal type from COMPUTER IN 1 and
COMPUTER IN 2 terminals.
„
„
RGB : For VGA signal
YCbCr/YPbPr:For component signal
Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
Message
Enable or disable the message box at the right bottom of the screen.
Auto Source
Automatically scan through all the input source.
Power Saving
If the input source is not detected and no operation is performed for a specific period of
time, projector will automatically turn off.
Green Mode
Enable this function when power consumption is under 1W.
2
29
Option
Closed Caption
Enable or disable closed captions by selecting CC1 (closed caption1, the most
common channel), CC2, CC3, CC4, T1, T2 or OFF.
DCR (Dynamic Contrast Ratio)
Enable DCR will further enhance contrast ratio by darkening the black scenes. Disable
DCR will resume to normal contrast performance. DCR will impact lamp life and
system noise performance.
Password
Set, change or delete the password. When the password function is added, image
projection will require to input the preset password when turning on the projector.
Presentation Timer
Remind the presenter to finish the presentation within a certain time frame.
High Altitude
Use this function to allow the fans operates at full speed continuously to achieve
proper high altitude cooling of the projector.
Lamp Setting
Allow you to enter the Lamp Setting menu.
„
„
„
Lamp Hours: Display the lamp’s elapsed operating time (in hours).
Lamp Hours Reset: Reset the lamp Hour to 0 hours.
ECO Mode: Use this function to dim the projector lamp light output which will
lower power consumption and increase lamp life. This function will be
unavailable when the DCR function is on.
My Button
Allow user to define a short cut key on the remote control, and the function item is
selected in OSD menu.
Test Pattern
Display embedded test pattern.
Factory Default
Restore settings to factory default.
Language
Select the language used by the on-screen menu.
Information
Input Source
Display the current input source.
Resolution
Display current input source resolution.
EN-30
30
H. Frequency
Display current image horizontal frequency.
V. Frequency
Display current image vertical frequency.
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
3
31
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning
Never open any of the covers on the projector. Dangerous electrical voltages
inside the projector can cause severe injury. Do not attempt to service this
product yourself. Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
„
Turn off the projector and remove the AC power cord from the power outlet
before beginning maintenance work.
„
„
Make sure the lens is cool before cleaning.
Do not use detergents or chemicals other than those noted above. Do not use
benzene or thinners.
„
„
Do not use chemical sprays.
Use a soft cloth or lens paper only.
EN-32
32
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
„
The lamp is extremely hot right after turning off the projector. If you touch the
lamp, you may scald your finger. When you replace the lamp, wait for at least
45 minutes for the lamp to cool down.
„
„
Do not touch the lamp glass at any time. The lamp may explode due to
improper handling, including the touching of the lamp glass.
Lamp lifetime may differ from lamp to lamp and according to the environment
of use. There is no guarantee of the same lifetime for each lamp. Some lamps
may fail or terminate their lifetime in a shorter period of time than other similar
lamps.
„
A lamp may explode as a result of vibration, shock or degradation as a result of
hours of use as its lifetime draws to an end. Risk of explosion may differ
according to the environment or conditions in which the projector and lamp are
being used.
„
„
Wear protective gloves and eyeglasses when fixing or detaching the lamp.
Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least
for 5 minutes to turn off the projector after powering on.
Do not operate the lamp in proximity to paper, cloth, or other combustible
material nor cover it with such materials.
Do not operate the lamp in an atmosphere containing an inflammable
substance, such as thinner.
Thoroughly ventilate the area or the room when operating the lamp in an
oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches,
nausea, dizziness, and other symptoms.
The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury
inside the lamp will be exposed. Leave the area immediately if the lamp
shatters while being operated and ventilate the area for at least 30 minutes in
order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to
user’s health.
„
„
„
„
3
33
1.
2.
3.
4.
5.
Turn off the projector.
If the projector is installed in a ceiling mount, remove it
Unplug the power cord.
Loosen the screw in the side of the lamp cover and remove the cover.
Remove the screws from the lamp module, raise the handle, and lift out the
module.
6.
7.
8.
Insert the new lamp module into the projector and tighten the screws.
Replace the lamp cover and tighten the screw.
Turn on the projector. If the lamp does not turn on after the warm-up period, try
reinstalling the lamp.
9.
Reset the lamp hour. Refer to the “Option > Lamp Setting” menu.
„
„
Dispose the used lamp according to local regulations.
Ensure that screws are tightened properly. Screws not tightened fully may
result in injury or accidents.
Since the lamp is made of glass, do not drop the unit and do not scratch the
glass.
Do not reuse the old lamp. This could cause the lamp to explode.
„
„
„
Be sure to turn off the projector and unplug the AC power cord before
replacing the lamp.
„
Do not use the projector with the lamp cover removed.
EN-34
34
Specifications
Display system
Resolution
Zoom
Single 0.55" DLP panel
XGA (1024 x 768 pixels)
Fixed
F/No.
0.68
Focal length
Screen size
Lamp
7.73 mm
40” - 300”
180W
Input terminal
D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal input (3.5
mm stereo mini jack) x 1, HDMI x 1
D-Sub 15 pin x 1, Audio signal output (3.5 mm stereo mini jack) x 1
RS-232 x 1, Mini USB type x1 (supports firmware upgrade and
remote mouse control)
Output terminal
Control terminal
Speaker
2 watt x 1
Video compatibility
NTSC, NTSC 4.43
PAL, PAL-N, PAL M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency
Environment
31 - 100 KHz
50 - 120 Hz
Operating:
Temperature: 0°C to 40°C
Humidity: 10%-80%
Storage:
Temperature: -20°C to 60°C
Humidity:30%-85%
AC 100-240 V, 50 - 60 Hz, 2.6A
245 W (Max.)
Power requirement
Power consumption
Dimension (W x D x H) 284.0 x 234.3 x 81.5 mm
Weight 2.6 kg (5.7 lb)
Note: Design and Specifications are subject to change without prior notice.
3
35
Dimensions
284.0 mm (W) x 234.3 mm (D) x 81.5 mm (H)
284.0
76.4
234.3
81.5
50.9
Ceiling mount installation
193.6
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
139.0
Unit: mm
210.6
EN-36
36
Appendix
LED Indicator Messages
LED Type
Color
Blue
Blue/Red Off
Status
Meaning
Power LED
Solid
Standby mode when green mode is turned on.
Temp/Lamp
LED
Power LED
Blue
Flash
Standby mode when green mode is turned off.
Powering up
Temp/Lamp
LED
Power LED
Blue/Red Off
Blue
Solid
Temp/Lamp
LED
Blue/Red Off
Power LED
Blue
Solid
Normal operation
Temp/Lamp
LED
Blue/Red Off
Power LED
Temp/Lamp
LED
Blue
Blue/Red Off
Flash
Powering down
(The projector needs to cool for 35 seconds after
the projector is turned off.)
Power LED
Temp/Lamp
LED
Blue
Magenta Flash
Flash
The projector system has some problems with its
fans, so the projector cannot start up.
Power LED
Temp/Lamp
LED
Blue
Lamp
(Red)
Solid
Flash
The lamp has reached its end of life and must be
changed soon. The lamp will continue to operate
until it fails. Change the lamp. If the lamp is off,
then the ballast will become malfunction.
Power LED
Temp/Lamp
LED
Blue
Temp
(Blue)
Solid
Flash
1. Temperature is too high. The lamp will turn off.
The fan motor is cooling the lamp.
Or
2. The cooling process is not complete after the
peojector is shut down and re-started right away.
Power LED
Temp/Lamp
LED
Blue
Magenta Flash
Solid
The lamp ignition failed. If temperature is too high,
the fans will cool the lamp.
3
37
Compatibility Modes
Computer:
Resolution
640 x 350
640 x 480
H-Sync [KHz]
V-Sync [Hz]
85.0
50.0
59.9
72.8
75.0
85.0
120.0
70.0
85.0
50.0
56.0
60.3
72.0
75.0
85.1
120.0
60.0
70.1
75.0
85.0
120.0
75.0
60.0
60.0
85.0
60.0
60.0
60.0
60,0
37.9
24.6
31.5
37.9
37.5
43.3
61.9
31.5
37.9
31.0
35.2
37.9
48.1
46.9
53.7
76.3
48.4
56.5
60.0
68.7
97.6
67.5
47.8
60.0
85.9
64.0
65.3
75.0
65,3
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 768
1280 x 960
1280 x 1024
1400 x 1050
1600 x 1200
1680 x 1050
EN-38
38
Video:
Compatibility
480i
Resolution
720 x 480
720 x 480
720 x 576
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
H-Sync [KHz]
15.8
V-Sync [Hz]
60
60
50
50
50
60
60
50
60
50
480p
576i
576p
720p
31.5
15.8
31.3
37.5
45
33.8
28.1
67.5
720p
1080i
1080i
1080p
1080p
56.3
3
39
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for
repairs. If the problem persists, contact your local reseller or service center. Please
refer to "LED Indicator Messages" as well.
Start-up problems
If no lights turn on:
„
Be sure that the power cord is securely connected to the projector and the other end
is plugged into an outlet with power.
„
„
Press the power button again.
Unplug the power cord and wait for a short while, then plug it in and press the power
button again.
Image problems
If the searching source is displayed:
„
Press SOURCE on the projector or Source on the remote control to select an
active input source.
„
„
Be sure the external source is turned on and connected.
For a computer connection, ensure your notebook computer’s external video port is
turned on. Refer to the computer manual.
If the image is out of focus:
„
While displaying the on-screen menu, adjust the focus ring. (The image size should
not change; if it does, you are adjusting the zoom, not the focus.)
Check the projection lens to see if it needs cleaning.
„
If the image is flickering or unstable for a computer connection:
„
Press MENU on the projector or Menu on the remote control, go to Video/Audio
and adjust Frequency or Tracking.
Remote control problems
If the remote control does not operate:
„
Be sure nothing is blocking the remote control receiver on the front of the
projector. Use the remote control within the effective range.
Aim the remote control at the screen or at the front of the projector.
Move the remote control so it is more directly in front of the projector and not as far
to the side.
„
„
EN-40
40
RS-232 Command and Configuration
Function
Action
Control Code
Return
Code
Power
Power on
Power off
Computer1
Computer2
S-Video
Video
BE,EF,10,05,00,C6,FF,11,11,01,00,01,00
BE,EF,03,06,00,DC,DB,69,00,00,00,00,00
BE,EF,03,19,00,19,29,01,47,02,CC,CC,00
BE,EF,03,19,1E,90,72,01,47,02,CC,CC,00
BE,EF,03,19,00,E8,69,01,47,02,CC,CC,00
BE,EF,03,19,00,78,A8,01,47,02,CC,CC,00
BE,EF,03,19,00,DA,2B,01,47,02,CC,CC,00
BE,EF,10,07,9F,9D,0E,0A,EF,00,00,00,00
BE,EF,10,07,9F,9D,0E,0A,EF,01,00,00,01
BE,EF,10,07,9F,9D,0E,0A,EF,02,00,00,02
BE,EF,10,07,9F,9D,0E,0A,EF,03,00,00,03
BE,EF,02,06,00,E9,D3,30,00,00,00,00,00
BE,EF,02,06,00,6D,D2,34,00,00,00,00,00
BE,EF,02,06,00,0B,D2,32,00,00,00,00,00
BE,EF,02,06,00,DA,D3,33,00,00,00,00,00
BE,EF,02,06,00,38,D2,31,00,00,00,00,00
BE,EF,03,06,00,EF,DB,6A,00,00,00,00,00
BE,EF,03,06,00,3E,DA,6B,00,00,00,00,00
BE,EF,03,06,00,BA,DB,6F,00,00,00,00,00
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
xxxx
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Source input
HDMI
Projector
position
Front table
Rear table
Front ceiling
Rear ceiling
Menu
Up
Down
Left
Right
ECO on
ECO off
Using hours
OSD
Lamp
Fan
Keystone
Aspect ratio
Blank
High Attitude on BE,EF,02,06,00,40,D3,80,00,00,00,00,01
High Attitude off BE,EF,02,06,00,40,D3,80,00,00,00,00,00
Keystone up
BE,EF,03,06,00,10,DB,65,00,00,00,00,00
Keystone down BE,EF,03,06,00,23,DB,66,00,00,00,00,00
4:3
16:9
BE,EF,03,06,00,0D,DA,68,00,01,00,00,01
BE,EF,03,06,00,0D,DA,68,00,02,00,00,02
BE,EF,02,06,00,DF,DF,66,00,01,00,00,01
BE,EF,02,06,00,DF,DF,66,00,02,00,00,02
BE,EF,02,06,00,02,D0,2B,00,01,00,00,01
BE,EF,02,06,00,02,D0,2B,00,02,00,00,02
BE,EF,02,06,00,F1,DE,68,00,00,00,00,00
BE,EF,02,06,00,20,DF,69,00,00,00,00,00
BE,EF,02,06,00,0E,DE,67,00,01,00,00,01
BE,EF,02,06,00,0E,DE,67,00,02,00,00,02
Blank on
Blank off
Freeze on
Freeze off
Volume +
Volume -
Mute on
Mute off
Freeze
Volume
Auto source Auto source on BE,EF,03,06,00,89,DB,6C,00,00,00,00,00
Auto source off BE,EF,03,06,00,58,DA,6D,00,00,00,00,00
6
6
Auto Sync
Factory
default
BE,EF,02,06,00,86,D1,2F,00,00,00,00,00
BE,EF,03,06,00,6B,DA,6E,00,00,00,00,00
6
6
4
41
Firmware
version
BE,EF,03,06,00,D5,D9,70,00,00,00,00,00 PXX37-9....
System
Status
BE,EF,03,06,00,04,D8,71,00,00,00,00,00
03=Power
On 00=Off
3D Sync
3D Sync on
3D Sync off
Brightest
PC
BE,EF,02,06,00,54,EF,7C,00,01,00,00,01
BE,EF,02,06,00,54,EF,7C,00,00,00,00,00
BE,EF,03,06,00,38,5A,88,12,08,08,12,08
BE,EF,03,06,00,38,5A,88,10,00,00,10,00
BE,EF,03,06,00,38,5A,88,13,01,01,13,01
BE,EF,03,06,00,38,5A,88,14,02,02,14,02
BE,EF,03,06,00,38,5A,88,15,05,05,15,05
BE,EF,03,06,00,38,5A,88,16,06,06,16,06
BE,EF,03,06,00,38,5A,88,17,07,07,17,07
BE,EF,03,06,00,38,5A,88,18,03,03,18,03
BE,EF,03,06,00,38,5A,88,19,04,04,19,04
BE,EF,1A,0C,00,09,0B,3A,00,01,00,00,01
BE,EF,1A,0C,00,09,0B,3A,00,02,00,00,02
BE,EF,1A,0C,00,09,0B,3A,00,03,00,00,03
BE,EF,1A,0C,00,09,0B,3A,00,04,00,00,04
BE,EF,1A,0C,00,09,0B,3A,00,05,00,00,05
BE,EF,1A,0C,00,09,0B,3A,00,06,00,00,06
BE,EF,1A,0C,00,09,0B,3A,00,07,00,00,07
BE,EF,1A,0C,00,09,0B,3A,00,08,00,00,08
BE,EF,1A,0C,00,09,0B,3A,00,09,00,00,09
BE,EF,1A,0C,00,09,0B,3A,00,0A,00,00,0A
BE,EF,1A,0C,00,09,0B,3A,00,0B,00,00,0B
BE,EF,1A,0C,00,09,0B,3A,00,0C,00,00,0C
BE,EF,1A,0C,00,09,0B,3A,00,0D,00,00,0D
BE,EF,1A,0C,00,09,0B,3A,00,0E,00,00,0E
BE,EF,1A,0C,00,09,0B,3A,00,0F,00,00,0F
BE,EF,1A,0C,00,09,0B,3A,00,10,00,00,10
BE,EF,1A,0C,00,09,0B,3A,00,11,00,00,11
BE,EF,02,06,00,22,55,76,00,00,00,00,01
BE,EF,02,06,00,22,55,76,00,00,00,00,00
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Color mode
Movie
ViewMatch
White Board
Black Board
Green Board
User 1
User 2
English
Nederlands
Français
Español
Language
Italiano
䚐ạ㛨
Åš¥
Português
᧯խ֮
ㅔԧЁ᭛
ᣣᧄ⺆
Ɋɭɫɫɤɢɣ
Deutsch
Svenska
Türkçe
Suomi
Polski
Magnify
Magnify Inc
Magnify Dec
Green Mode Green Mode On BE,EF,02,06,00,40,B5,86,00,00,00,00,01
Green Mode Off BE,EF,02,06,00,40,B5,86,00,00,00,00,00
DCR
DCR On
DCR Off
BE,EF,02,06,00,D3,D1,2A,00,00,00,00,00
BE,EF,03,06,00,EE,DA,6B,00,00,00,00,00
EN-42
42
!!!!!!!!!
D-Sub 9 pin
Wire List
COLOR
Black
Brown
Red
Orange
Yellow
Green
Blue
1
2
3
4
5
6
7
8
9
1 CD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
C1
1
2
3
4
5
6
7
C2
1
2
3
4
5
6
7
8
9
Purple
White
DW
8
9
SHELL
SHELL
4
43
IR Control Code
System Code: 83F4
Format : NEC
64
67
8D
87
65
02
66
6B
84
82
8C
85
83
81
0A
03
63
88
89
8B
0F
80
68
6A
8E
8F
EN-44
44
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
T = Telephone
F = FAX
Country/Region
Website
Email
AUS= 1800 880 818
NZ= 0800 008 822
Australia/New Zealand
T (Toll-Free)= 1-866-
463-4775
T (Toll)= 1-424-233-2533
F= 1-909-468-3757
Canada
com
Europe
Hong Kong
India
com/uk/
T= 852 3102 2900
T= 1800 266 0101
service_ie@
Ireland (Eire)
Korea
Latin America
(Argentina)
Latin America (Chile)
Latin America
(Columbia)
com/uk/support/call-desk/ viewsoniceurope.com
T= 080 333 2131
T= 0800-4441185
T= 1230-020-7975
T= 01800-9-157235
T= 001-8882328722
/DWLQꢁ$PHULFDꢁꢃ0H[LFRꢄ
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
(OHFWURVHUꢂꢁ$Yꢁ5HIRUPDꢁ1Rꢀꢁꢅꢆꢇ*[ꢇꢈꢁ\ꢁꢅꢉꢂꢁꢈꢊꢆꢆꢆꢁ0pULGDꢂꢁ<XFDWiQꢀꢁ7HOꢋꢁꢆꢉꢀꢈꢈꢈꢀꢈꢌꢍꢀꢉꢈꢀꢉꢎ
2WKHUꢁSODFHVꢁSOHDVHꢁUHIHUꢁWRꢁKWWSꢋꢏꢏZZZꢀYLHZVRQLFꢀFRPꢏODꢏVRSRUWHꢏLQGH[ꢀKWPꢐ0H[LFR
Latin America (Peru)
Macau
Middle East
ap.viewsonic.com/me/
T= 0800-54565
T= 853 2870 0303
Contact your reseller
T= 1-800-688-6688
(English)
T= 1-866-379-1304
(Spanish)
Puerto Rico & Virgin
Islands
F= 1-909-468-3757
Singapore/Malaysia/
Thailand
South Africa
ap.viewsonic.com/za/
com/uk/
T= 65 6461 6044
Contact your reseller
com/uk/support/call-desk/ viewsoniceurope.com
service_gb@
United Kingdom
T (Toll-Free)= 1-800-
688-6688
T (Toll)= 1-424-233-2530
United States
F= 1-909-468-3757
45
Limited Warranty
®
VIEWSONIC PROJECTOR
What the warranty covers:
9LHZ6RQLFꢀZDUUDQWVꢀLWVꢀSURGXFWVꢀWRꢀEHꢀIUHHꢀIURPꢀGHIHFWVꢀLQꢀPDWHULDOꢀDQGꢀZRUNPDQVKLSꢐꢀXQGHUꢀ
normal use, during the warranty period. If a product proves to be defective in material or
ZRUNPDQVKLSꢀGXULQJꢀWKHꢀZDUUDQW\ꢀSHULRGꢐꢀ9LHZ6RQLFꢀZLOOꢐꢀDWꢀLWVꢀVROHꢀRSWLRQꢐꢀUHSDLUꢀRUꢀUHSODFHꢀ
the product with a like product. Replacement product or parts may include remanufactured or
refurbished parts or components.
Limited Three (3) year General Warranty
6XEMHFWꢀWRꢀWKHꢀPRUHꢀOLPLWHGꢀRQHꢀꢍꢈꢎꢀ\HDUꢀZDUUDQW\ꢀVHWꢀRXWꢀEHORZꢐꢀ1RUWKꢀDQGꢀ6RXWKꢀ$PHULFDꢑꢀ7KUHHꢀ
ꢍꢅꢎꢀ\HDUVꢀZDUUDQW\ꢀIRUꢀDOOꢀSDUWVꢀH[FOXGLQJꢀWKHꢀODPSꢐꢀWKUHHꢀꢍꢅꢎꢀ\HDUVꢀIRUꢀODERUꢐꢀDQGꢀRQHꢀꢍꢈꢎꢀ\HDUꢀIRUꢀ
WKHꢀRULJLQDOꢀODPSꢀIURPꢀWKHꢀGDWHꢀRIꢀWKHꢀ¿UVWꢀFRQVXPHUꢀSXUFKDVHꢔꢀ(XURSHꢀH[FHSWꢀ3RODQGꢑꢀ7KUHHꢀꢍꢅꢎꢀ
\HDUVꢀZDUUDQW\ꢀIRUꢀDOOꢀSDUWVꢀH[FOXGLQJꢀWKHꢀODPSꢐꢀWKUHHꢀꢍꢅꢎꢀ\HDUVꢀIRUꢀODERUꢐꢀDQGꢀQLQHW\ꢀꢍꢋꢄꢎꢀGD\VꢀIRUꢀ
WKHꢀRULJLQDOꢀODPSꢀIURPꢀWKHꢀGDWHꢀRIꢀWKHꢀ¿UVWꢀFRQVXPHUꢀSXUFKDVHꢔꢀ3RODQGꢑꢀ7ZRꢀꢍꢆꢎꢀ\HDUVꢀZDUUDQW\ꢀ
IRUꢀDOOꢀSDUWVꢀH[FOXGLQJꢀWKHꢀODPSꢐꢀWZRꢀꢍꢆꢎꢀ\HDUVꢀIRUꢀODERUꢐꢀDQGꢀQLQHW\ꢀꢍꢋꢄꢎꢀGD\VꢀIRUꢀWKHꢀRULJLQDOꢀ
ODPSꢀIURPꢀWKHꢀGDWHꢀRIꢀWKHꢀ¿UVWꢀFRQVXPHUꢀSXUFKDVHꢁꢀ
Limited One (1) year Heavy Usage Warranty:
8QGHUꢀKHDY\ꢀXVDJHꢀVHWWLQJVꢐꢀZKHUHꢀDꢀSURMHFWRU¶VꢀXVHꢀLQFOXGHVꢀPRUHꢀWKDQꢀIRXUWHHQꢀꢍꢈꢇꢎꢀKRXUVꢀ
DYHUDJHꢀGDLO\ꢀXVDJHꢐꢀ1RUWKꢀDQGꢀ6RXWKꢀ$PHULFDꢑꢀ2QHꢀꢍꢈꢎꢀ\HDUꢀZDUUDQW\ꢀIRUꢀDOOꢀSDUWVꢀH[FOXGLQJꢀ
WKHꢀODPSꢐꢀRQHꢀꢍꢈꢎꢀ\HDUꢀIRUꢀODERUꢐꢀDQGꢀQLQHW\ꢀꢍꢋꢄꢎꢀGD\VꢀIRUꢀWKHꢀRULJLQDOꢀODPSꢀIURPꢀWKHꢀGDWHꢀRIꢀWKHꢀ
¿UVWꢀFRQVXPHUꢀSXUFKDVHꢔꢀ(XURSHꢑꢀ2QHꢀꢍꢈꢎꢀ\HDUꢀZDUUDQW\ꢀIRUꢀDOOꢀSDUWVꢀH[FOXGLQJꢀWKHꢀODPSꢐꢀRQHꢀ
ꢍꢈꢎꢀ\HDUꢀIRUꢀODERUꢐꢀDQGꢀQLQHW\ꢀꢍꢋꢄꢎꢀGD\VꢀIRUꢀWKHꢀRULJLQDOꢀODPSꢀIURPꢀWKHꢀGDWHꢀRIꢀWKHꢀ¿UVWꢀFRQVXPHUꢀ
purchase.
2WKHUꢀUHJLRQVꢀRUꢀFRXQWULHVꢑꢀ3OHDVHꢀFKHFNꢀZLWKꢀ\RXUꢀORFDOꢀGHDOHUꢀRUꢀORFDOꢀ9LHZ6RQLFꢀRI¿FHꢀIRUꢀ
the warranty information.
/DPSꢀZDUUDQW\ꢀVXEMHFWꢀWRꢀWHUPVꢀDQGꢀFRQGLWLRQVꢐꢀYHUL¿FDWLRQꢀDQGꢀDSSURYDOꢁꢀ$SSOLHVꢀWRꢀ
manufacturer’s installed lamp only. All accessory lamps purchased separately are warranted
IRUꢀꢋꢄꢀGD\Vꢁ
Who the warranty protects:
7KLVꢀZDUUDQW\ꢀLVꢀYDOLGꢀRQO\ꢀIRUꢀWKHꢀ¿UVWꢀFRQVXPHUꢀSXUFKDVHUꢁ
What the warranty does not cover:
1.ꢀ $Q\ꢀSURGXFWꢀRQꢀZKLFKꢀWKHꢀVHULDOꢀQXPEHUꢀKDVꢀEHHQꢀGHIDFHGꢐꢀPRGL¿HGꢀRUꢀUHPRYHGꢁ
2.ꢀ 'DPDJHꢐꢀGHWHULRUDWLRQꢐꢀIDLOXUHꢐꢀRUꢀPDOIXQFWLRQꢀUHVXOWLQJꢀIURPꢑ
Dꢁꢀ ꢀ$FFLGHQWꢐꢀDEXVHꢐꢀPLVXVHꢐꢀQHJOHFWꢐꢀ¿UHꢐꢀZDWHUꢐꢀOLJKWQLQJꢐꢀRUꢀRWKHUꢀDFWVꢀRIꢀQDWXUHꢐꢀ
LPSURSHUꢀPDLQWHQDQFHꢐꢀXQDXWKRUL]HGꢀSURGXFWꢀPRGL¿FDWLRQꢐꢀRUꢀIDLOXUHꢀWRꢀIROORZꢀ
instructions supplied with the product.
ꢀ
Eꢁꢀ 2SHUDWLRQꢀRXWVLGHꢀRIꢀSURGXFWꢀVSHFL¿FDWLRQVꢁ
c. Operation of the product for other than the normal intended use or not under normal
conditions.
ꢀ
Gꢁꢀ 5HSDLUꢀRUꢀDWWHPSWHGꢀUHSDLUꢀE\ꢀDQ\RQHꢀQRWꢀDXWKRUL]HGꢀE\ꢀ9LHZ6RQLFꢁ
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
46
ꢀ
ꢀ
ꢀ
Jꢁꢀ &DXVHVꢀH[WHUQDOꢀWRꢀWKHꢀSURGXFWꢐꢀVXFKꢀDVꢀHOHFWULFꢀSRZHUꢀÀXFWXDWLRQVꢀRUꢀIDLOXUHꢁ
Kꢁꢀ 8VHꢀRIꢀVXSSOLHVꢀRUꢀSDUWVꢀQRWꢀPHHWLQJꢀ9LHZ6RQLF¶VꢀVSHFL¿FDWLRQVꢁ
Lꢁꢀ 1RUPDOꢀZHDUꢀDQGꢀWHDUꢁ
j. Any other cause which does not relate to a product defect.
3. 5HPRYDOꢐꢀLQVWDOODWLRQꢐꢀDQGꢀVHWꢃXSꢀVHUYLFHꢀFKDUJHVꢁ
How to get service:
1. ꢀ ꢀ)RUꢀLQIRUPDWLRQꢀDERXWꢀUHFHLYLQJꢀVHUYLFHꢀXQGHUꢀZDUUDQW\ꢐꢀFRQWDFWꢀ9LHZ6RQLFꢀ&XVWRPHUꢀ
6XSSRUWꢀꢍSOHDVHꢀUHIHUꢀWRꢀ³&XVWRPHUꢀ6XSSRUW´ꢀSDJHꢎꢁꢀ<RXꢀZLOOꢀQHHGꢀWRꢀSURYLGHꢀ\RXUꢀ
product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b)
your name, (c) your address, (d) a description of the problem, and (e) the serial number of the
product.
3.ꢀꢀ ꢀ7DNHꢀRUꢀVKLSꢀWKHꢀSURGXFWꢀIUHLJKWꢀSUHSDLGꢀLQꢀWKHꢀRULJLQDOꢀFRQWDLQHUꢀWRꢀDQꢀDXWKRUL]HGꢀ
9LHZ6RQLFꢀVHUYLFHꢀFHQWHUꢀRUꢀ9LHZ6RQLFꢁꢀ
4.ꢀꢀ ꢀ)RUꢀDGGLWLRQDOꢀLQIRUPDWLRQꢀRUꢀWKHꢀQDPHꢀRIꢀWKHꢀQHDUHVWꢀ9LHZ6RQLFꢀVHUYLFHꢀFHQWHUꢐꢀFRQWDFWꢀ
9LHZ6RQLFꢁꢀ
Limitation of implied warranties:
7KHUHꢀDUHꢀQRꢀZDUUDQWLHVꢐꢀH[SUHVVꢀRUꢀLPSOLHGꢐꢀZKLFKꢀH[WHQGꢀEH\RQGꢀWKHꢀGHVFULSWLRQꢀFRQWDLQHGꢀ
KHUHLQꢀLQFOXGLQJꢀWKHꢀLPSOLHGꢀZDUUDQW\ꢀRIꢀPHUFKDQWDELOLW\ꢀDQGꢀ¿WQHVVꢀIRUꢀDꢀSDUWLFXODUꢀSXUSRVHꢁꢀ
Exclusion of damages:
9LHZ6RQLF¶VꢀOLDELOLW\ꢀLVꢀOLPLWHGꢀWRꢀWKHꢀFRVWꢀRIꢀUHSDLUꢀRUꢀUHSODFHPHQWꢀRIꢀWKHꢀSURGXFWꢁꢀ9LHZ6RQLFꢀ
shall not be liable for:
1.ꢀꢀ ꢀ'DPDJHꢀWRꢀRWKHUꢀSURSHUW\ꢀFDXVHGꢀE\ꢀDQ\ꢀGHIHFWVꢀLQꢀWKHꢀSURGXFWꢐꢀGDPDJHVꢀEDVHGꢀXSRQꢀ
LQFRQYHQLHQFHꢐꢀORVVꢀRIꢀXVHꢀRIꢀWKHꢀSURGXFWꢐꢀORVVꢀRIꢀWLPHꢐꢀORVVꢀRIꢀSUR¿WVꢐꢀORVVꢀRIꢀEXVLQHVVꢀ
opportunity, loss of goodwill, interference with business relationships, or other commercial
loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of state law:
7KLVꢀZDUUDQW\ꢀJLYHVꢀ\RXꢀVSHFL¿FꢀOHJDOꢀULJKWVꢐꢀDQGꢀ\RXꢀPD\ꢀDOVRꢀKDYHꢀRWKHUꢀULJKWVꢀZKLFKꢀYDU\ꢀ
IURPꢀVWDWHꢀWRꢀVWDWHꢁꢀ6RPHꢀVWDWHVꢀGRꢀQRWꢀDOORZꢀOLPLWDWLRQVꢀRQꢀLPSOLHGꢀZDUUDQWLHVꢀDQGꢂRUꢀGRꢀQRWꢀ
DOORZꢀWKHꢀH[FOXVLRQꢀRIꢀLQFLGHQWDOꢀRUꢀFRQVHTXHQWLDOꢀGDPDJHVꢐꢀVRꢀWKHꢀDERYHꢀOLPLWDWLRQVꢀDQGꢀ
H[FOXVLRQVꢀPD\ꢀQRWꢀDSSO\ꢀWRꢀ\RXꢁꢀ
Sales outside the U.S.A. and Canada:
)RUꢀZDUUDQW\ꢀLQIRUPDWLRQꢀDQGꢀVHUYLFHꢀRQꢀ9LHZ6RQLFꢀSURGXFWVꢀVROGꢀRXWVLGHꢀRIꢀWKHꢀ8ꢁ6ꢁ$ꢁꢀDQGꢀ
&DQDGDꢐꢀFRQWDFWꢀ9LHZ6RQLFꢀRUꢀ\RXUꢀORFDOꢀ9LHZ6RQLFꢀGHDOHUꢁꢀ
7KHꢀZDUUDQW\ꢀSHULRGꢀIRUꢀWKLVꢀSURGXFWꢀLQꢀPDLQODQGꢀ&KLQDꢀꢍ+RQJꢀ.RQJꢐꢀ0DFDRꢀDQGꢀ7DLZDQꢀ
([FOXGHGꢎꢀLVꢀVXEMHFWꢀWRꢀWKHꢀWHUPVꢀDQGꢀFRQGLWLRQVꢀRIꢀWKHꢀ0DLQWHQDQFHꢀ*XDUDQWHHꢀ&DUGꢁ
)RUꢀXVHUVꢀLQꢀ(XURSHꢀDQGꢀ5XVVLDꢐꢀIXOOꢀGHWDLOVꢀRIꢀZDUUDQW\ꢀSURYLGHGꢀFDQꢀEHꢀIRXQGꢀLQꢀZZZꢁ
YLHZVRQLFHXURSHꢁFRPꢀXQGHUꢀ6XSSRUWꢂ:DUUDQW\ꢀ,QIRUPDWLRQꢁ
ꢇꢁꢅꢑꢀ3URMHFWRUꢀ:DUUDQW\ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ35-B/:ꢄꢈꢀ5HYꢁꢀꢈKꢀꢄꢊꢃꢆꢌꢃꢄꢕ
47
Mexico Lim®ited Warranty
VIEWSONIC PROJECTOR
What the warranty covers:
9LHZ6RQLFꢀZDUUDQWVꢀLWVꢀSURGXFWVꢀWRꢀEHꢀIUHHꢀIURPꢀGHIHFWVꢀLQꢀPDWHULDOꢀDQGꢀZRUNPDQVKLSꢐꢀXQGHUꢀQRUPDOꢀ
use, during the warranty period. If a product proves to be defective in material or workmanship during
WKHꢀZDUUDQW\ꢀSHULRGꢐꢀ9LHZ6RQLFꢀZLOOꢐꢀDWꢀLWVꢀVROHꢀRSWLRQꢐꢀUHSDLUꢀRUꢀUHSODFHꢀWKHꢀSURGXFWꢀZLWKꢀDꢀOLNHꢀSURGXFWꢁꢀ
5HSODFHPHQWꢀSURGXFWꢀRUꢀSDUWVꢀPD\ꢀLQFOXGHꢀUHPDQXIDFWXUHGꢀRUꢀUHIXUELVKHGꢀSDUWVꢀRUꢀFRPSRQHQWVꢀ ꢀDFFHVVRULHVꢁ
How long the warranty is effective:
ꢅꢀ\HDUVꢀIRUꢀDOOꢀSDUWVꢀH[FOXGLQJꢀWKHꢀODPSꢐꢀꢅꢀ\HDUVꢀIRUꢀODERUꢐꢀꢈꢀ\HDUꢀIRUꢀWKHꢀRULJLQDOꢀODPSꢀIURPꢀWKHꢀGDWHꢀRIꢀWKHꢀ¿UVWꢀFRQVXPHUꢀ
purchase.
/DPSꢀZDUUDQW\ꢀVXEMHFWꢀWRꢀWHUPVꢀDQGꢀFRQGLWLRQVꢐꢀYHUL¿FDWLRQꢀDQGꢀDSSURYDOꢁꢀ$SSOLHVꢀWRꢀPDQXIDFWXUHU¶VꢀLQVWDOOHGꢀODPSꢀRQO\ꢁ
$OOꢀDFFHVVRU\ꢀODPSVꢀSXUFKDVHGꢀVHSDUDWHO\ꢀDUHꢀZDUUDQWHGꢀIRUꢀꢋꢄꢀGD\Vꢁ
Who the warranty protects:
7KLVꢀZDUUDQW\ꢀLVꢀYDOLGꢀRQO\ꢀIRUꢀWKHꢀ¿UVWꢀFRQVXPHUꢀSXUFKDVHUꢁ
What the warranty does not cover:
ꢈꢁꢀ $Q\ꢀSURGXFWꢀRQꢀZKLFKꢀWKHꢀVHULDOꢀQXPEHUꢀKDVꢀEHHQꢀGHIDFHGꢐꢀPRGL¿HGꢀRUꢀUHPRYHGꢁ
ꢆꢁꢀ 'DPDJHꢐꢀGHWHULRUDWLRQꢀRUꢀPDOIXQFWLRQꢀUHVXOWLQJꢀIURPꢑ
ꢀ
Dꢁꢀ ꢀ$FFLGHQWꢐꢀPLVXVHꢐꢀQHJOHFWꢐꢀ¿UHꢐꢀZDWHUꢐꢀOLJKWQLQJꢐꢀRUꢀRWKHUꢀDFWVꢀRIꢀQDWXUHꢐꢀXQDXWKRUL]HGꢀSURGXFWꢀ
PRGL¿FDWLRQꢐꢀXQDXWKRUL]HGꢀDWWHPSWHGꢀUHSDLUꢐꢀRUꢀIDLOXUHꢀWRꢀIROORZꢀLQVWUXFWLRQVꢀVXSSOLHGꢀZLWKꢀWKHꢀ
product.
b. Any damage of the product due to shipment.
ꢀ
ꢀ
ꢀ
Fꢁꢀ ꢀ&DXVHVꢀH[WHUQDOꢀWRꢀWKHꢀSURGXFWꢐꢀVXFKꢀDVꢀHOHFWULFDOꢀSRZHUꢀÀXFWXDWLRQVꢀRUꢀIDLOXUHꢁ
Gꢁꢀ 8VHꢀRIꢀVXSSOLHVꢀRUꢀSDUWVꢀQRWꢀPHHWLQJꢀ9LHZ6RQLF¶VꢀVSHFL¿FDWLRQVꢁ
Hꢁꢀ 1RUPDOꢀZHDUꢀDQGꢀWHDUꢁ
f. Any other cause which does not relate to a product defect.
ꢅꢁꢀ ꢀ$Q\ꢀSURGXFWꢀH[KLELWLQJꢀDꢀFRQGLWLRQꢀFRPPRQO\ꢀNQRZQꢀDVꢀ³LPDJHꢀEXUQꢃLQ´ꢀZKLFKꢀUHVXOWVꢀZKHQꢀDꢀVWDWLFꢀ
LPDJHꢀLVꢀGLVSOD\HGꢀRQꢀWKHꢀSURGXFWꢀIRUꢀDQꢀH[WHQGHGꢀSHULRGꢀRIꢀWLPHꢁ
ꢇꢁꢀ ꢀ5HPRYDOꢐꢀLQVWDOODWLRQꢐꢀLQVXUDQFHꢐꢀDQGꢀVHWꢃXSꢀVHUYLFHꢀFKDUJHVꢁ
How to get service:
)RUꢀLQIRUPDWLRQꢀDERXWꢀUHFHLYLQJꢀVHUYLFHꢀXQGHUꢀZDUUDQW\ꢐꢀFRQWDFWꢀ9LHZ6RQLFꢀ&XVWRPHUꢀ6XSSRUWꢀꢍ3OHDVHꢀUHIHUꢀWRꢀ
WKHꢀDWWDFKHGꢀ&XVWRPHUꢀ6XSSRUWꢀSDJHꢎꢁꢀ<RXꢀZLOOꢀQHHGꢀWRꢀSURYLGHꢀ\RXUꢀSURGXFW¶VꢀVHULDOꢀQXPEHUꢐꢀVRꢀSOHDVHꢀUHFRUGꢀ
the product information in the space provided below on your purchase for your future use. Please retain your
receipt of proof of purchase to support your warranty claim.
For Your Records
3URGXFWꢀ1DPHꢑꢀBBBBBBBBBBBBBBBBBBBBBBBBꢀ
'RFXPHQWꢀ1XPEHUꢑꢀBBBBBBBBBBBBBBBBBBBBꢀ
3XUFKDVHꢀ'DWHꢑꢀBBBBBBBBBBBBBBBBBBBBBBBBꢀ
1ꢎ
0RGHOꢀ1XPEHUꢑꢀBBBBBBBBBBBBBBBBBBBBBBBBBB
6HULDOꢀ1XPEHUꢑꢀBBBBBBBBBBBBBBBBBBBBBBBBBBB
([WHQGHGꢀ:DUUDQW\ꢀ3XUFKDVH"ꢀBBBBBBBBBBBBBBBꢍ<ꢂ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
,IꢀVRꢐꢀZKDWꢀGDWHꢀGRHVꢀZDUUDQW\ꢀH[SLUH"ꢀBBBBBBBBB
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
ꢆꢁꢀ ꢀ7DNHꢀRUꢀVKLSꢀWKHꢀSURGXFWꢀLQꢀWKHꢀRULJLQDOꢀFRQWDLQHUꢀSDFNDJLQJꢀWRꢀDQꢀDXWKRUL]HGꢀ9LHZ6RQLFꢀVHUYLFHꢀFHQWHUꢁ
ꢅꢁꢀ 5RXQGꢀWULSꢀWUDQVSRUWDWLRQꢀFRVWVꢀIRUꢀLQꢃZDUUDQW\ꢀSURGXFWVꢀZLOOꢀEHꢀSDLGꢀE\ꢀ9LHZ6RQLFꢁ
Limitation of implied warranties:
7KHUHꢀDUHꢀQRꢀZDUUDQWLHVꢐꢀH[SUHVVꢀRUꢀLPSOLHGꢐꢀZKLFKꢀH[WHQGꢀEH\RQGꢀWKHꢀGHVFULSWLRQꢀFRQWDLQHGꢀKHUHLQꢀLQFOXGLQJꢀ
WKHꢀLPSOLHGꢀZDUUDQW\ꢀRIꢀPHUFKDQWDELOLW\ꢀDQGꢀ¿WQHVVꢀIRUꢀDꢀSDUWLFXODUꢀSXUSRVHꢁ
Exclusion of damages:
9LHZ6RQLF¶VꢀOLDELOLW\ꢀLVꢀOLPLWHGꢀWRꢀWKHꢀFRVWꢀRIꢀUHSDLUꢀRUꢀUHSODFHPHQWꢀRIꢀWKHꢀSURGXFWꢁꢀ9LHZ6RQLFꢀVKDOOꢀQRWꢀEHꢀOLDEOHꢀIRUꢑ
ꢈꢁꢀ ꢀ'DPDJHꢀWRꢀRWKHUꢀSURSHUW\ꢀFDXVHGꢀE\ꢀDQ\ꢀGHIHFWVꢀLQꢀWKHꢀSURGXFWꢐꢀGDPDJHVꢀEDVHGꢀXSRQꢀLQFRQYHQLHQFHꢐꢀ
ORVVꢀRIꢀXVHꢀRIꢀWKHꢀSURGXFWꢐꢀORVVꢀRIꢀWLPHꢐꢀORVVꢀRIꢀSUR¿WVꢐꢀORVVꢀRIꢀEXVLQHVVꢀRSSRUWXQLW\ꢐꢀORVVꢀRIꢀJRRGZLOOꢐꢀ
interference with business relationships, or other commercial loss, even if advised of the possibility of
such damages.
2. Any other damages, whether incidental, consequential or otherwise.
ꢅꢁꢀ $Q\ꢀFODLPꢀDJDLQVWꢀWKHꢀFXVWRPHUꢀE\ꢀDQ\ꢀRWKHUꢀSDUW\ꢁ
ꢇꢁꢀ 5HSDLUꢀRUꢀDWWHPSWHGꢀUHSDLUꢀE\ꢀDQ\RQHꢀQRWꢀDXWKRUL]HGꢀE\ꢀ9LHZ6RQLFꢁ
48
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
0p[LFRꢐꢀ$YꢁꢀGHꢀODꢀ3DOPDꢀꢖꢉꢀ3LVRꢀꢆꢀ'HVSDFKRꢀꢆꢄꢅꢐꢀ&RUSRUDWLYRꢀ,QWHUSDOPDVꢐ
&ROꢁꢀ6DQꢀ)HUQDQGRꢀ+XL[TXLOXFDQꢐꢀ(VWDGRꢀGHꢀ0p[LFR
7HOꢑꢀꢍꢌꢌꢎꢀꢅꢊꢄꢌꢃꢈꢄꢋꢋꢀꢀꢀꢀꢀKWWSꢑꢂꢂZZZꢁYLHZVRQLFꢁFRPꢂODꢂVRSRUWHꢂLQGH[ꢁKWP
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Villahermosa:
'LVWULEXFLRQHVꢀ\ꢀ6HUYLFLRVꢀ&RPSXWDFLRQDOHVꢀ6$ꢀ &RPSXPDQWHQLPLHWQRVꢀ*DUDQWL]DGRVꢐꢀ6ꢁ$ꢁꢀGHꢀ&ꢁ9ꢁ
GHꢀ&9ꢁ
$9ꢁꢀ*5(*25,2ꢀ0(1'(=ꢀꢖꢈꢌꢄꢇ
&2/ꢐꢀ)/25,'$ꢀ&ꢁ3ꢁꢀꢉꢊꢄꢇꢄ
7HOꢑꢀꢄꢈꢀꢍꢋꢋꢅꢎꢀꢅꢀꢌꢆꢀꢄꢄꢀꢇꢕꢀꢂꢀꢅꢌꢆꢆꢄꢕꢇꢀꢂꢀꢅꢀꢌꢆꢀꢆꢄꢀꢄꢋ
(ꢃ0DLOꢑꢀFRPSXPDQWHQLPLHQWRV#SURGLJ\ꢁQHWꢁP[
&DOOHꢀ-XDUH]ꢀꢆꢉꢇꢀORFDOꢀꢆ
&ROꢁꢀ%XJDPELOLDVꢀ&ꢁ3ꢑꢀꢉꢅꢈꢇꢄ
7HOꢑꢀꢄꢈꢃꢊꢊꢃꢆꢆꢃꢈꢇꢃꢋꢄꢄꢌ
(ꢃ0DLOꢑꢀGLVFꢆ#KPRꢁPHJDUHGꢁQHWꢁP[
Puebla, Pue. (Matriz):
Veracruz, Ver.:
5(17$ꢀ<ꢀ'$726ꢐꢀ6ꢁ$ꢁꢀ'(ꢀ&ꢁ9ꢁꢀ'RPLFLOLRꢑ
ꢆꢋꢀ685ꢀꢕꢆꢈꢀ&2/ꢁꢀ/$ꢀ3$=
&21(;,21ꢀ<ꢀ'(6$552//2ꢐꢀ6ꢁ$ꢀ'(ꢀ&ꢁ9ꢁꢀꢀ$Yꢁꢀ$PHULFDVꢀꢖꢀꢇꢈꢋ
(175(ꢀ3,1=Ï1ꢀ<ꢀ$/9$5$'2
)UDFFꢁꢀ5HIRUPDꢀ&ꢁ3ꢁꢀꢋꢈꢋꢈꢋ
ꢕꢆꢈꢊꢄꢀ38(%/$ꢐꢀ38(ꢁ
7HOꢑꢀꢄꢈꢍꢌꢆꢎꢁꢆꢆꢆꢁꢉꢋꢈꢁꢌꢌꢁꢕꢕꢀ&21ꢀꢈꢄꢀ/,1($6
(ꢃ0DLOꢑꢀGDWRV#SXHEODꢁPHJDUHGꢁQHWꢁP[
7HOꢑꢀꢄꢈꢃꢆꢆꢃꢋꢈꢃꢄꢄꢃꢅꢈꢃꢊꢕ
(ꢃ0DLOꢑꢀJDFRVWD#TSOXVꢁFRPꢁP[
Chihuahua
Cuernavaca
6ROXFLRQHVꢀ*OREDOHVꢀHQꢀ&RPSXWDFLyQ
&ꢁꢀ0DJLVWHULRꢀꢖꢀꢅꢅꢆꢈꢀ&ROꢁꢀ0DJLVWHULDO
Chihuahua, Chih.
&RPSXVXSSRUWꢀGHꢀ&XHUQDYDFDꢀ6$ꢀGHꢀ&9
)UDQFLVFRꢀ/H\YDꢀꢖꢀꢈꢕꢉꢀ&ROꢁꢀ0LJXHOꢀ+LGDOJR
&ꢁ3ꢁꢀꢊꢆꢄꢇꢄꢐꢀ&XHUQDYDFDꢀ0RUHORV
7HOꢑꢀꢄꢈꢀꢕꢕꢕꢀꢅꢈꢉꢄꢌꢕꢋꢀꢂꢀꢄꢈꢀꢕꢕꢕꢀꢅꢈꢆꢇꢄꢈꢇ
(ꢃ0DLOꢑꢀDTXHYHGR#FRPSXVXSSRUWFYDꢁFRP
7HOꢑꢀꢇꢈꢅꢊꢋꢌꢇ
(ꢃ0DLOꢑꢀ&HIHR#VROXJOREDOHVꢁFRP
Distrito Federal:
Guadalajara, Jal.:
43/86ꢐꢀ6ꢁ$ꢁꢀGHꢀ&ꢁ9ꢁ
6(59,&5(&(ꢐꢀ6ꢁ$ꢁꢀGHꢀ&ꢁ9ꢁ
$Yꢁꢀ1LxRVꢀ+pURHVꢀꢖꢀꢆꢆꢉꢈ
&ROꢁꢀ$UFRVꢀ6XUꢐꢀ6HFWRUꢀ-XiUH]
ꢇꢇꢈꢕꢄꢐꢀ*XDGDODMDUDꢐꢀ-DOLVFR
7HOꢑꢀꢄꢈꢍꢌꢆꢎꢅꢅꢃꢅꢊꢃꢈꢌꢃꢈꢌꢃꢇꢅ
(ꢃ0DLOꢑꢀPPLUDQGD#VHUYLFUHFHꢁFRP
$Yꢁꢀ&R\RDFiQꢀꢋꢅꢈ
&ROꢁꢀ'HOꢀ9DOOHꢀꢄꢅꢈꢄꢄꢐꢀ0p[LFRꢐꢀ'ꢁ)ꢁ
7HOꢑꢀꢄꢈꢍꢌꢆꢎꢌꢌꢃꢌꢄꢃꢄꢄꢃꢆꢕꢃꢅꢌ
(ꢃ0DLOꢀꢑꢀJDFRVWD#TSOXVꢁFRPꢁP[
Guerrero Acapulco
Monterrey:
*6ꢀ&RPSXWDFLyQꢀꢍ*UXSRꢀ6HVLFRPSꢎ
3URJUHVRꢀꢖꢊꢃ$ꢐꢀ&RORꢀ&HQWUR
ꢅꢋꢅꢄꢄꢀ$FDSXOFRꢐꢀ*XHUUHUR
7HOꢑꢀꢕꢇꢇꢃꢇꢉꢃꢅꢆꢊꢆꢕ
*OREDOꢀ3URGXFWꢀ6HUYLFHV
0DUꢀ&DULEHꢀꢖꢀꢈꢋꢉꢕꢐꢀ(VTXLQDꢀFRQꢀ*ROIRꢀ3pUVLFR
)UDFFꢁꢀ%HUQDUGRꢀ5H\HVꢐꢀ&3ꢀꢊꢇꢆꢉꢄ
0RQWHUUH\ꢀ1ꢁ/ꢁꢀ0p[LFR
7HOꢑꢀꢉꢈꢆꢋꢃꢌꢈꢄꢅ
(ꢃ0DLOꢑꢀD\GHHP#JSVꢈꢁFRPꢁP[
MERIDA:
Oaxaca, Oax.:
(/(&7526(5
&(1752ꢀ'(ꢀ',675,%8&,21ꢀ<
6(59,&,2ꢐꢀ6ꢁ$ꢁꢀGHꢀ&ꢁ9ꢁ
$Yꢀ5HIRUPDꢀ1Rꢁꢀꢇꢄꢅ*[ꢅꢋꢀ\ꢀꢇꢈ
0pULGDꢐꢀ<XFDWiQꢐꢀ0p[LFRꢀꢀ&3ꢋꢕꢄꢄꢄ
7HOꢑꢀꢍꢌꢆꢎꢀꢋꢋꢋꢃꢋꢆꢌꢃꢈꢋꢈꢊ
(ꢃ0DLOꢑꢀUUUE#VXUHVWHꢁFRP
0XUJXtDꢀꢖꢀꢕꢄꢉꢀ3ꢁ$ꢁꢐꢀ&ROꢁꢀ&HQWURꢐꢀꢊꢉꢄꢄꢄꢐꢀ2D[DFD
7HOꢑꢀꢄꢈꢍꢌꢆꢎꢋꢌꢃꢈꢌꢃꢈꢌꢃꢆꢆꢃꢆꢆ
)D[ꢑꢀꢄꢈꢍꢌꢆꢎꢋꢌꢃꢈꢌꢃꢈꢅꢃꢊꢕꢃꢄꢄꢀ
(ꢃ0DLOꢁꢀJSRWDLꢆꢄꢄꢈ#KRWPDLOꢁFRP
Tijuana:
67'
FOR USA SUPPORT:
9LHZ6RQLFꢀ&RUSRUDWLRQꢀ
$Yꢀ)HUURFDUULOꢀ6RQRUDꢀꢖꢅꢕꢉꢄꢀ/ꢃ&ꢀ
&ROꢀꢆꢄꢀGHꢀ1RYLHPEUH
7LMXDQDꢐꢀ0H[LFR
ꢅꢉꢈꢀ%UHDꢀ&DQ\RQꢀ5RDGꢐꢀ:DOQXWꢐꢀ&$ꢁꢀꢋꢈꢕꢉꢋꢀ86$
7HOꢑꢀꢉꢄꢄꢃꢊꢉꢉꢃꢊꢊꢉꢉꢀꢍ(QJOLVKꢎꢔꢀꢀꢉꢊꢊꢃꢅꢆꢅꢃꢉꢄꢌꢊꢀꢍ6SDQLVKꢎꢔ
)D[ꢑꢀꢈꢃꢉꢄꢄꢃꢊꢉꢌꢃꢕꢆꢕꢊ
(ꢃ0DLOꢑꢀKWWSꢑꢂꢂZZZꢁYLHZVRQLFꢁFRP
ꢇꢁꢅꢑꢀ9LHZ6RQLFꢀ0H[LFRꢀ/LPLWHGꢀ:DUUDQW\ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ35-B/:ꢄꢅꢀ5HYꢁꢀꢈ$ꢀꢄꢊꢃꢆꢌꢃꢄꢕ
49
|