OWNER'S MANUAL
For use only with models: TRU446, TRU4465, TRU448, TRU4485, TRUC46 (Card Phone)
As an Energy Star® Partner, Uniden has determined that
this product or product models meets the Energy Star®
guidelines for energy efficiency.
Energy Star® is a U.S. registered mark.
THE FCC WANTS YOU TO KNOW
Changes or modifications to this product not expressly approved by
Uniden, or operation of this product in any way other than as detailed
by the owner's manual, could void your authority to operate this product.
May be covered under one or more of the following U.S. patents:
Welcome
Congratulations on your purchase of the Uniden TXC400 optional
handset and charger. This additional handset is for use with the
Uniden TRU446, TRU448, TRU4465, TRU4485, or TRUC46 (Card
Phone) base. You can place a fully featured cordless handset
anywhere in your home where AC power is available to connect
the handset charger. The original base will support up to 2
handsets (the original handset and one TXC400 handset).
The TXC400 will not be an alternative of the original handset,
if the original handset is damaged.
Important
The TXC400 will not operate unless it has been registered to a
Uniden TRU446, TRU448, TRU4465, TRU4485, or TRUC46 (Card
Phone). Before the additional handset can be used, the battery
must be charged and it must be registered with the base.
This manual describes only the instructions specific to the
additional handset. For detailed operation, refer to the owner’s
manual supplied with the original unit (read “Expanding Your
Phone” chapter first).
Checking the Package Contents
Make sure you have received the following items in the package.
If any of these items are missing or damaged, contact the
Uniden Parts Department.
• Cordless Handset
• Charger
• Battery Pack (BT-446)
(Capacity: 800 mAH, 3.6V)
• AC Adapter (AD-446)
(INPUT: 120V AC 60Hz) (OUTPUT: 9V DC 210 mA)
• Beltclip
• This Owner’s Manual
• Other Printed Material
Uniden Parts Department at (800) 554-3988
Hours: M-F 7:00 a.m. to 5:00 p.m. CST.
We can also be reached on the web at
– 2 –
Install the Battery Pack
Charge the battery pack for at least 15-20 hours before
completing the installation or using the handset.
Press down on the battery cover
release and slide the cover down until
it comes off.
1
Connect the battery pack connector
2
observing the correct polarity (black
and red wires) to the jack inside the
battery compartment.
Do not exert any force on this
connection. It could cause damage to the
battery or to the handset. The plastic
connectors will fit in only one way.
Once you are certain that you have made
a good connection, then insert the
battery pack into the battery
compartment. Do not pinch the wires.
Securely close the battery
compartment cover by sliding it until
it snaps into place.
3
Place the handset in the charging
cradle with the keypad facing forward.
4
• Use only the Uniden battery (BT-446)
supplied with your phone. Replacement
batteries are also available through the
Uniden Parts Department. (See page 2)
• Recharge your handset on a regular basis
by returning the handset to the charger
after each phone call.
Battery Information
Battery use time (per charge)
From fully charged (15-20 hours charge time)
• 6 hours continuous use
• 10 days when the handset is in the standby mode
– 3 –
Low battery alert
When the battery pack is very low and needs to be charged, the
phone is programmed to eliminate functions in order to save
power. If the phone is in the standby mode, ”Low Battery”
appears on the LCD and none of the keys will operate. If the
phone is in use, ”Low Battery” appears and the handset
beeps. Complete your conversation as quickly as possible and
return the handset to the base unit for charging.
Cleaning the battery charging contacts
To maintain a good charge, it is
important to clean the battery
contacts on the handset and base
unit with a dry cloth or a pencil
eraser about once a month.
Do not use any liquids or solvents.
contacts
Connect the Charger
Connect the AC adapter
1
to the DC IN 9V jack
and to a standard 120V
AC wall outlet.
Set the charger on a
2
desk or tabletop, and
place the handset in the
charger with the keypad
facing forward.
Make sure that the
3
charger LED illuminates. If the LED does not illuminate,
check to see that the AC adapter is plugged in and that the
handset makes good contact with the base charging contacts.
• Use only the supplied AD-446
Polarity of the plug
AC adapter. Do not use any other
AC adapter.
• Place the charger close to the AC
outlet so that you can unplug the
AC adapter easily.
• ”HS2” appears on the display
while the handset is charging.
– 4 –
Register the Handset
You need to register the TXC400 before use.
To register the additional handset, do the following steps in
compliance with your original unit.
For TRU446/TRU4465/TRU448/TRU4485 unit
Place the TXC400 handset on the original unit’s base until you
hear a confirmation tone. If the original base is mounted, you
will need to hold the handset to the base until the status LED
on the unit’s base is illuminated.
•
If the original base is a TRU448, to register the TXC400, place
the TXC400 on the TRU448 base with the keypad facing down.
• If you did not hear the confirmation tone, register the
TXC400 again.
• In some cases you may need to attempt registration
a few times.
For TRUC46 (Card Phone) unit
Unplug the AC adapter of the TRUC46.
1
2
Press and hold PAGE on the TRUC46 base, while you plug in
the AC Adapter, until the status LED on the base flashes.
Press talk/flash on the TXC400’s handset.
3
“Handset Registering” appears. When the
operation is finished, you will hear a confirmation tone and
“Registration Complete” will appear. The status
LED is no longer illuminated.
• If the registration fails, “Registration Failed”
appears. Register the TXC400 again.
• You must complete the registration operation within 30
seconds, or the phone returns to the standby mode.
If you changed the digital security code of the original unit:
You need to perform the following steps:
De-register the digital security code of the TXC400. (For
instructions, see “Change the Digital Security Code” in the
owner’s manual supplied with the original unit.
1
Register the TXC400 to the original base by following the
steps above.
2
– 5 –
Call Transfer Feature
You can transfer an outside call to the original unit. For
more instructions, see the owner’s manual supplied with the
original unit.
To transfer a call to the
original unit
Press xfer/del during a call.
When the original unit receives the
transfered call, the TXC400 handset
returns to the standby mode.
To receive a transferred call
from the original unit
Press talk/flash to answer the
transferred call.
To cancel the transfer
Press talk/flash or xfer/del.
If you transfer a call and it is not picked up after 5 minutes,
you hear a beep, and the call will be disconnected.
Using the TXC400 with the
Integrated Answering Device
If the original unit has a built-in answering system, you can
check your new messages, skip, repeat, or delete your messages
with the TXC400 handset. For more instructions, see the owner’s
manual supplied with original unit.
To playback a message
To skip a message
Press -.
Press 3.
To repeat the current message
Press 1 after four seconds.
To repeat the previous message Press 1 within four seconds.
To delete a message
To stop operation
Press 4.
Press end.
• If you press end before the answering system answers, the
phone will return to the standby mode.
• When the answering system does not answer within 7
seconds, you will hear a beep and the phone will return to
the standby mode.
• When you receive a call, the remote operation is canceled.
– 6 –
One Year Limited Warranty
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the original retail owner, this
Uniden Product to be free from defects in materials and craftsmanship with only the
limitations or exclusions set out below.
WARRANTY DURATION: This warranty to the original user shall terminate and be of no further
effect 12 months after the date of original retail sale. The warranty is invalid if the Product
is (A) damaged or not maintained as reasonable or necessary, (B) modified, altered, or used
as part of any conversion kits, subassemblies, or any configurations not sold by Uniden,
(C) improperly installed, (D) serviced or repaired by someone other than an authorized
Uniden service center for a defect or malfunction covered by this warranty, (E) used in any
conjunction with equipment or parts or as part of any system not manufactured by Uniden,
or (F) installed or programmed by anyone other than as detailed by the owner’s manual for
this product.
STATEMENT OF REMEDY: In the event that the product does not conform to this warranty at
any time while this warranty is in effect, warrantor will either repair or replace the defective
unit and return it to you without charge for parts, service, or any other cost (except
shipping and handling) incurred by warrantor or its representatives in connection with the
performance of this warranty. Warrantor may replace the unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING
TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE
WHATSOEVER, WHETHER EXPRESSED, IMPLIED OR ARISING BY OPERATION OF LAW, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR THE
REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do
not allow this exclusion or limitation of incidental or consequential damages so the above
limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. This warranty is void outside the United States of
America.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after following the instructions
in the owner’s manual you are certain that the Product is defective, pack the Product
carefully (preferably in its original packaging). The Product should include all parts and
accessories originally packaged with the Product. Include evidence of original purchase and a
note describing the defect that has caused you to return it. The Product should be shipped
freight prepaid, by traceable means, to warrantor at:
Uniden America Corporation
Parts and Service Division
4700 Amon Carter Blvd.
Fort Worth, TX 76155
(800) 297-1023, 8 a.m. to 5 p.m. Central, Monday through Friday
– 7 –
|