INSTALL GUIDE
KE-4 KEYLESS ENTRY SYSTEM
U.S.A. Model
WWW.ULTRASTARTERS.COM
Technical Support
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the part responsible for compliance
void the user’s authority to operate this devise.
Installation Manual
KE-4
Park Lights (+)
Chassis Ground
Main Power (+)
Ignition (+)
15 Amp Output
Ground Input
White
Black
Red
LT
-
Constant 12 volts
Ignition Input
+
Yellow
IG
Un2
500ma Output
Pink
2nd Unlock (-)
1st Unlock (-)
Lock (-)
UN
LK
Blue
Green
Gray
500ma Output
500ma Output
500ma Output
Ch2
HR
ST
Trunk Rel. Out (-)
(-) Horn Honk
Starter Kill (+)
Brown
500ma Output
500ma Output
Orange
Antenna - Do Not Ground the
antenna wire.
***500ma outputs are low current and are designed to activate relays.
Installation Manual
KE-4
STEP 1 - The following wires MUST be connected for proper operation.
Red
12vt Power
Ignition
(+) 15amp Input
(+) 12volt Input
Constant 12vt power sourse.
Main ignition wire.
Yellow
White
Black
Green
Blue
Park Lights
Ground
(+) 15amp Output Connect to positive park lights
(-) Input Connect to chassis ground.
(-)500ma Output Connect to door lock relay.
Lock Output
Unlock Output (-)500ma Output Connect to door unlock relay.
Optional Connections
Orange
Brown
Gr ey
St.Disable (-)500ma Output Connect to Starter Disable relay.
Horn Output (-)500ma Output Connect to horn relay.
Trunk Output (-)500ma Output Connect to Trunk Release relay.
2nd Unlock (-)500ma Output Connect when installing Driver's Door Priority.
Pink
STEP 2 - CONNECT AND MOUNT THE MODULE
Plug the Connectors into the Module. Press the transmitter buttons to check for
proper operation. Once it is determined that everything is working correctly the module
can be mounted.
***Before plugging the module in make sure that Ignition Key is in the OFF position***
Mount the module by selecting a location under the dash that is secure.
Be certain that the module does not obstruct any serviceable areas. The
module must be free from moving parts such as brake, clutch and gas
pedals and the linkages that are attached to them.
Basic remote operations
Lock
Unlock
Trunk
See Owners Manual for more transmitter
operations
Installation Manual
KE-4
TRANSMITTER PROGRAMMING
To add additional transmitters and delete existing transmitter code(s) from memory.
1) Turn the ignition On-Off-On-Off-On-Off-On-Off. The park lights will flash twice.
2) Press the Lock button on the transmitters to be programmed.
3) The park lights will flash once, each time a new transmitter is learned.
*** If this does not happen wait ten seconds and repeat steps 1-3.
Note: Each system can store a maximum of three transmitter codes in memory.
Transmitter Program on “Power Up”
1) Plug in the module. (Leave the ignition in the Off position).
2) Press the lock button on each of the transmitters to be programmed.
3) The park lights will flash once each time a new transmitter code is learned.
Note: Previous transmitters that are not programmed at this time will deleted from memory.
SYSTEM RESET
Reset To Factory Default Settings.
1) Make sure ignition is in the OFF position.
2) Turn the ignition key ON - leaving key in the ON position.
3) Press the transmitter buttons as follows. Trunk-Lock-Unlock-Trunk.
4) The system will respond by flashing the park lights three times
The system is now set to factory default settings.
QUICK VIEW PROGRAM MENU
Entering The Program Menu
1) Make sure ignition is in the OFF position.
2) Turn the ignition key ON - leaving key in the ON position.
3) Press the transmitter buttons in the appropriate sequence.
4) After ten seconds the system will automatically exit Program Mode.
To change a Programmable Feature press the transmitter buttons as follows.
*** Default settings are shown in bold lettering.
Passive / Active Arming
Passive / Active Locks
Lock-Unlock-Lock-Unlock
Passive
Active
Unlock-Trunk-Unlock-Trunk Passive
Active
Ignition Aouto Door Locks Lock-Trunk-Lock-Trunk
ON
OFF
Door Lock Pulses
Double Pulse
Lock-Unlock-Trunk-Lock
Three Second
.75 Second
Single Pulse
OFF
Unlock-Trunk-Unlock-Lock Double Pulse
Passive Warning Chirps
Lock-Trunk-Unlock-Trunk
ON
Reset To FactoryDefaults Trunk-Lock-Unlock-Trunk
Three flashes
Three Flashes
Installation Manual
KE-4
Entering The Program Menu
1) Make sure ignition is in the OFF position.
2) Turn the ignition key ON - leaving key in the ON position.
3) Press the transmitter button in the appropriate sequence.
4) After ten seconds the system will automatically exit Program Mode.
Setting 1 - Passive/Active Mode (Factory Default Setting: Active Mode)
Passive mode means that the system will automatically arm thirty seconds after
The ignition key is turned off and the last door of the vehicle is closed.
Sometimes referred to as Automatic Arming.
Active mode means that the system will not arm until you manually turn it on by
pressing the lock button on your transmitter.
1. Turn the ignition on. Ignition on means normal driving position.
2. Within 10 seconds, press and release the transmitter buttons
Lock Unlock Lock Unlock in succession.
PASSIVE MODE is confirmed with one horn chirp sound and one light flash.
ACTIVE MODE is confirmed with two horn chirp sounds and two light flashes.
Setting 2 - Passive Lock Mode (Factory Default Setting: Active Lock Mode)
Passive Lock Mode means that all doors will lock automatically when the system
arms in the passive mode.
Active Lock Mode means that doors will lock only with the lock button.
1 Turn the ignition on. Ignition on means normal driving position.
2 Within 10 seconds, press and release the transmitter buttons
Unlock Trunk Unlock Trunk in succession.
PASSIVE LOCK MODE is confirmed with one horn chirp sound and one parking
light flash.
ACTIVE LOCK MODE is confirmed with two horn chirp sounds and two parking
Light flashes.
CAUTION: If the automatic door lock feature is installed and the system is
Programmed to passive lock mode the doors will lock automatically when the
system arms. It is always advisable to remove the ignition key each time you exit
the vehicle.
Setting 3 - Ignition Auto Locks (Factory Default Setting: Locks Off)
Ignition Lock Mode means that all doors will lock automatically two (2)Seconds after
the ignition key is turned on and will unlock automatically when the ignition
key is turned off. This assumes that the keyless entry option has been installed
by your Dealer. Sometimes referred to as Ignition Lock.
1 Turn the ignition on. Ignition on means normal driving position.
2 Within 10 seconds, press and release the transmitter button
Lock Trunk Lock Trunk in succession.
DRIVE LOCK MODE ON is confirmed with one horn chirp sound and one parking light
flash.
DRIVE LOCK MODE OFF is confirmed with two horn chirp sounds and two parking
light flashes.
Installation Manual
Setting 4 - Long Door Lock Pulse (Factory Default Setting: Pulse Off)
KE-4
Long Door Lock Pulse means that the system can accommodate the factory
central locking systems of import vehicles having vacuum door lock actuators that
require a three-second lock pulse.
1 Turn the ignition on. Ignition on means normal driving position.
2 Within 10 seconds, press and release the transmitter buttons
Lock Unlock Trunk Lock in succession.
LONG DOOR LOCK PULSE MODE is confirmed with one parking light flash.
SHORT DOOR LOCK PULSE MODE is confirmed with two parking light flashes.
Setting 5 - Dual Unlock Pulse (Factory Default Setting: Dual Unlock Mode Off)
Dual Unlock Pulse means that the system can accommodate the factory central locking
systems of import vehicles having dual unlock pulse to unlock the driver and passenger
doors.
1 Turn the ignition on. Ignition on means normal driving position.
2 Within 10 seconds, press and release the transmitter buttons
Unlock Trunk Unlock Lock in succession.
DUAL PULSE ON is confirmed with one horn chirp sound and one parking light flash.
DUAL PULSE OFF is confirmed with two horn chirp sounds and two parking light flashes.
Setting 6 - Passive Warning Chirp (Factory Default Setting: Warning Chirp Off)
Passive Warning Chirp means that in passive mode (4.1) the system gives soft
Warming chirp sounds during thirty second arming period after each temporary disarm.
1Turn the ignition on. Ignition on means normal driving position.
2Within 10 seconds, press and release the transmitter button
Lock Trunk Unlock Trunk in succession.
CHIRP ON is confirmed with one horn chirp sound and one parking light flash.
CHIRP OFF is confirmed with two horn chirp sounds and two parking light flashes.
Setting 7 -Reset to Factory Default
To Reset all programmable features to factory default setting:
1 Turn the ignition on. Ignition on means normal driving position.
2 Within 10 seconds, press and release the transmitter button
Trunk Lock Unlock Trunk in succession.
Reset to factory default is confirmed with three horn chirp sounds and three park
Light flashes.
Installation Manual
KE-4
POSITIVE TRUNK RELEASE
Trunk Release Solenoid
Trunk Release
Switch
87
+12V
Grey
87a
86
85
30
NEGATIVE PARK LIGHTS
Parking
Light Switch
Parking Lights
Ground
87
White
87a
86
85
30
STARTER KILL
IG2
ACC
Off
IG1
Start
Cut
x
To Starter Motor
or Relay
87
87a
86
85
30
Orange
|